2011 GT Muffler Weight

[wbt]

For those who are curious, they weigh 21lbs. each for a total of 42lbs.

The Magnaflow muffler deletes in box shipped weigh 22lbs..

Without packing and box, you are looking at about a 22lbs. weight savings. The nice thing about this is when you begin adding control arms, relocation brackets and rear girdle/axle tube braces, you are probably a little ahead of the weight game. :thumb:

[GrnBullitt08]

hmmm...noted

[beefcake]

the stainless works new chambered system outta come in pretty nice as well, probably will be the lightest out of all of them.

[beefcake]

http://www.new-used-ford-cars-trucks-for-sale-bankruptcy-special-financing.com/sw7.jpg

[killr3v]

Dumps would be the lightest lol

[wbt]

the stainless works new chambered system outta come in pretty nice as well, probably will be the lightest out of all of them.

Overall exhaust probably. Comparing axle back muffler to muffler delete definately not.

[me32]

http://www.new-used-ford-cars-trucks-for-sale-bankruptcy-special-financing.com/sw7.jpg

what are those

[beefcake]

what are those

stainless works exhaust

[wbt]

stainless works exhaust

Looks very similar to the stock resonators. I'll take a pic of mine and post later.

[Boorail85]

I really want to hear that stainless works kit. I bet it sounds killer.

[Twinscrewgt]

Those look nothing like the stock resonators.. And I too am curious to the noise.

[wbt]

Those look nothing like the stock resonators.. And I too am curious to the noise.

Really....

http://i632.photobucket.com/albums/uu48/wbthurber/2011%20Mustang%20GT/CIMG0680.jpg
http://i632.photobucket.com/albums/uu48/wbthurber/2011%20Mustang%20GT/CIMG0677.jpg

Minus the indentions.

SSW appears to be a fluted design.

[Twinscrewgt]

Minus the indentations, length and diameter.. yup look exactly the same. Anyways.. any sound clips?

[wbt]

Minus the indentations, length and diameter.. yup look exactly the same. Anyways.. any sound clips?

How about more community contribution vs. following everyone's posts?

:thumb:

[Lightblade]

Minus the indentations, length and diameter.. yup look exactly the same. Anyways.. any sound clips?

haha! its like that saying: for 5 dollars the flowers are free.



Those look nothing like the stock resonators.. And I too am curious to the noise.

+1000.


How about more community contribution vs. following everyone's posts?

:thumb:

Hate to break it to ya man, but they look nothing alike. :stfu:

[STEWIE]

That actually has a chamber in it. It is a retro style system similar to what cars from the late 60's and early 70's had on it. The system on beefcakes car from what the guys at stainless works say has 2 of those on each side; one in the location as seen in the pic and another pair where the mufflers go.

I was at their car show this weekend and it does sound sweet!!!
They are supposedly going to have sound clips soon.

[beefcake]

here is a pic of the 2nd set of chambers

i should have a sound clip this afternoon without headers, and then they are going to be putting headers on the car

http://www.new-used-ford-cars-trucks-for-sale-bankruptcy-special-financing.com/sw6.jpg

[beefcake]

fyi,

anthony said they weighed the stock system from the h pipe back, came out to 78lbs,

their 3" system with the regular chambered mufflers came in at 55 lbs, so 23 lb savings.

he thinks this system is going to come in around 50lbs for a total of 28lb savings

[beefcake]

That actually has a chamber in it. It is a retro style system similar to what cars from the late 60's and early 70's had on it. The system on beefcakes car from what the guys at stainless works say has 2 of those on each side; one in the location as seen in the pic and another pair where the mufflers go.

I was at their car show this weekend and it does sound sweet!!!
They are supposedly going to have sound clips soon.

heres a guys t/a i know, think it's a 96

http://i70.photobucket.com/albums/i96/torchd02ta/Exhaust/DSC03583.jpg

[beefcake]

I really want to hear that stainless works kit. I bet it sounds killer.

well, here ya go

this is without the long tubes and high flow cats

http://www.youtube.com/watch?v=Z3J8rLhYykU

[STEWIE]

heres a guys t/a i know, think it's a 96

http://i70.photobucket.com/albums/i96/torchd02ta/exhaust/dsc03583.jpg


yup that's what i was talking about! Thanks beef

[GeorgeInNePa]

What's the cost on that, approximately?

[46foxcoupe]

For those who are curious, they weigh 21lbs. each for a total of 42lbs.

The Magnaflow muffler deletes in box shipped weigh 22lbs..

Without packing and box, you are looking at about a 22lbs. weight savings. The nice thing about this is when you begin adding control arms, relocation brackets and rear girdle/axle tube braces, you are probably a little ahead of the weight game. :thumb:

I just put a flowmaster hushpower axleback on mine. weighed both. stock weighed 42. flowmasters were 24.

[Twinscrewgt]

I just put a flowmaster hushpower axleback on mine. weighed both. stock weighed 42. flowmasters were 24.

Sound clip?

[46foxcoupe]

Sound clip?

http://www.youtube.com/watch?v=pBfaIAf49ic&hd=1

[mpf]

Hey, sorry to post the foto again...I have the same dent on my drivers side,
also..this is a pic of factory pipes, correct?
Took it in, they threw it on the lift, and said they would get a new one
"when the part showed up on the computer"

Really....

http://i632.photobucket.com/albums/uu48/wbthurber/2011%20Mustang%20GT/CIMG0677.jpg

Minus the indentions.

SSW appears to be a fluted design.

[Twinscrewgt]

http://www.youtube.com/watch?v=pBfaIAf49ic&hd=1

man that sounds amazing!! How much did you pay for it?

[46foxcoupe]

here's a link to them on our website:

http://www.latemodelrestoration.com/item/FLO-819109/2011-Mustang-Gt-50L-Flowmaster-Hushpower-Axle-Back-Exhaust

[LRSJarrod]

You can pre-order them now. They are on a P/O and we should have them here in a few business days!

[PLACECRAFT20]

I would like to know what kind of in the car drone you get with either of these setups. 2000 rpm cruise. Will it drive you nuts on a long trip?
Thanks

[46foxcoupe]

I would like to know what kind of in the car drone you get with either of these setups. 2000 rpm cruise. Will it drive you nuts on a long trip?
Thanks

I've experienced none of that 2000 rpm drone with the Hushpowers that you use to get with the old 2 chamber flowmasters.

[PLACECRAFT20]

I've experienced none of that 2000 rpm drone with the Hushpowers that you use to get with the old 2 chamber flowmasters.

Thanks, yours sounds good. Who did your programming?

[46foxcoupe]

Thanks, yours sounds good. Who did your programming?

SCT handheld with their canned tune. Nothing special. Pulled it off the shelf and plugged it in.

[wbt]

Hey, sorry to post the foto again...I have the same dent on my drivers side,
also..this is a pic of factory pipes, correct?
Took it in, they threw it on the lift, and said they would get a new one
"when the part showed up on the computer"

Yes factory. The indentations are there on all cars. That is due to the machines used to hold them in manufacturing. Not a big deal TBH. Replacing will not help in any way. If you are really bothered by it, replace it with a cat-back of your choice. ;)

[BAKnBLK2010]

For those who are curious, they weigh 21lbs. each for a total of 42lbs.

The Magnaflow muffler deletes in box shipped weigh 22lbs..

Without packing and box, you are looking at about a 22lbs. weight savings. The nice thing about this is when you begin adding control arms, relocation brackets and rear girdle/axle tube braces, you are probably a little ahead of the weight game. :thumb:


I can't believe those things retail for $600.00 bucks. Did you find them for less???

[wbt]

I can't believe those things retail for $600.00 bucks. Did you find them for less???

I paid just over $400 which is still too much IMO. $200-$250 is fair but parts for these cars aren't cheap atm. Maybe a different story in another year.

[mpf]

Yes factory. The indentations are there on all cars. That is due to the machines used to hold them in manufacturing.)

Thanks...was getting ready to call dealer back and ask 'what's with the wait'.