Heaten m90
forum member
- Joined
- Jun 3, 2017
- Posts
- 335
- Reaction score
- 8
Going to try'n consolidate my posts'. Got 2 builds going on right now. My turbo 427R and my ol'ladies 98 TJ that she wants coyote swapped. I'll be doing all the work to both, but she'll be paying for her parts. the jeeps going to be used to trailer the mustang. Her budget is only about 10 grand, so I don't know if it's even going to be possible. I have about 12 grand left for my project and can use anything that's left over on the jeep. Below is the parts I already have. But I still need to figure out what crank I'm going to use and what my fuel system will support. I plan on purchasing MMR chain tensioners and guilds as well a MMR trigger wheel, gear, felpro head gaskets tonight. Im thinking of doing a gforce tr3650 rebuild with a crash box/dog rings. (Have a friend that works in gas turbine R&D department and Can make custom CNC parts if I make the auto cad drawings) still haven't decided on which turbo setup I'll be running or if I'll be running an aftermarket ECM as well as what valves and valve springs are needed. I'll be posting a lot of YouTube videos through the entire project. Hopefully when I'm done it'll be a badass no prep/street racing car.
-Diamond -6cc pistons standard bore pistons
-AP total seal steel ring set
-4130 chrome moly .150 wrist pins
-clevite H series bearings
-ATI harmonic balancer super damper/ ARP Bolt
-FRPP rockers/adjusters
-ARP 156-5002 side bolts
-ARP 156-5902 main studs
-ARP 2000 rod bolts
-ARP 2000 head studs
-MSD 2 step
-FRPP hot rod cams
-greddy profec electronic boost controller
-80 LBS Ford racing injectors 10AWG wiring upgrade
-Ford racing fuel rail spacer kit
-400 LPH walbro pump with 8AWG wiring kit upgraded & performance driver module
-Kenny bell BAP 17.5 volt
-brisk 3VR14S
-62MM FRPP Throttle body
-dorman intake manifold
-billet aluminum intake runners/charge motion delete
-MSD street fighter coils 10 AWG wiring upgrade
-heavy-duty roush tensioner
-EBay shorty stainless headers
- ford racing A/C delete
-160 thermostat
-Ford racing valve covers
-mishimoto hoses
-aluminum block
-Percision CNC performance cam Phasers with TTY bolts and timing tool
-NRK o2 sensors
Drivetrain:
-TR3650
- 4" aluminum drive shaft
-ACT prolight XACT lightweight chromoly flywheel
-McLeod super street (spare ACT stage 4 clutch)
-RAM adjustable Hydraulic TOB( spare McLeod TOB )
-FRPP steel slave cylinder
-braided stainless steel hydraulic lines
-RAM pedal height adjuster
-Ford racing grade 9 bell housing bolt kit
-Ford racing extreme duty M series pilot bearing
-ford racing differential cooler/cover
-Ford racing 3.31 gears (have spare 4.10.s
-Ford racing 8.8 carbon rebuild kit
Suspension:
-BMR motor mounts with solid billet pucks
-full Roush stage 3 suspension
-cobra jet drag springs
-BMR LCA with relocation brackets
-GT500 strut mounts
-BMR sub frame connectors
-steeda x brace
-steeda rear strut tower brace
-s&w 8 point roll cage with roush 5 point harnesses (3")
-BMR k-member brace
Interior:
-Kirkey 71 series driver Kirkey 495 series passenger full containment seats
-Full Roush carbon fiber dash
-Roush short throw shifter
-full weight reduction(gutted)
-truck bed liner on all the tin
-Sparco steering wheel hub adapter
-NRG steering wheel quick release
-CZR titanium steering wheel spacer
-holly sniper can shift light
-Dash 3 pod gauge cluster(oil,fuel LED with warnings)
-innovative LM2 A/F wide band
-roush vent pod/ boost gauge
-SCT x4
-coldfire/ fire suppression system
-sparco/FRPP steering wheel
Exterior:
-VIS racing carbon fiber super snake hood functional heat extractors and ram intake
-roush 427R body kit
-Roush 18" forged aluminum rims
-Rear: Hoosier 315X30X18 DR2 slick with 2" billet spacer
-Front: Hoosier 295x30x18 A7 slick with 1" billet spacer
-Diamond -6cc pistons standard bore pistons
-AP total seal steel ring set
-4130 chrome moly .150 wrist pins
-clevite H series bearings
-ATI harmonic balancer super damper/ ARP Bolt
-FRPP rockers/adjusters
-ARP 156-5002 side bolts
-ARP 156-5902 main studs
-ARP 2000 rod bolts
-ARP 2000 head studs
-MSD 2 step
-FRPP hot rod cams
-greddy profec electronic boost controller
-80 LBS Ford racing injectors 10AWG wiring upgrade
-Ford racing fuel rail spacer kit
-400 LPH walbro pump with 8AWG wiring kit upgraded & performance driver module
-Kenny bell BAP 17.5 volt
-brisk 3VR14S
-62MM FRPP Throttle body
-dorman intake manifold
-billet aluminum intake runners/charge motion delete
-MSD street fighter coils 10 AWG wiring upgrade
-heavy-duty roush tensioner
-EBay shorty stainless headers
- ford racing A/C delete
-160 thermostat
-Ford racing valve covers
-mishimoto hoses
-aluminum block
-Percision CNC performance cam Phasers with TTY bolts and timing tool
-NRK o2 sensors
Drivetrain:
-TR3650
- 4" aluminum drive shaft
-ACT prolight XACT lightweight chromoly flywheel
-McLeod super street (spare ACT stage 4 clutch)
-RAM adjustable Hydraulic TOB( spare McLeod TOB )
-FRPP steel slave cylinder
-braided stainless steel hydraulic lines
-RAM pedal height adjuster
-Ford racing grade 9 bell housing bolt kit
-Ford racing extreme duty M series pilot bearing
-ford racing differential cooler/cover
-Ford racing 3.31 gears (have spare 4.10.s
-Ford racing 8.8 carbon rebuild kit
Suspension:
-BMR motor mounts with solid billet pucks
-full Roush stage 3 suspension
-cobra jet drag springs
-BMR LCA with relocation brackets
-GT500 strut mounts
-BMR sub frame connectors
-steeda x brace
-steeda rear strut tower brace
-s&w 8 point roll cage with roush 5 point harnesses (3")
-BMR k-member brace
Interior:
-Kirkey 71 series driver Kirkey 495 series passenger full containment seats
-Full Roush carbon fiber dash
-Roush short throw shifter
-full weight reduction(gutted)
-truck bed liner on all the tin
-Sparco steering wheel hub adapter
-NRG steering wheel quick release
-CZR titanium steering wheel spacer
-holly sniper can shift light
-Dash 3 pod gauge cluster(oil,fuel LED with warnings)
-innovative LM2 A/F wide band
-roush vent pod/ boost gauge
-SCT x4
-coldfire/ fire suppression system
-sparco/FRPP steering wheel
Exterior:
-VIS racing carbon fiber super snake hood functional heat extractors and ram intake
-roush 427R body kit
-Roush 18" forged aluminum rims
-Rear: Hoosier 315X30X18 DR2 slick with 2" billet spacer
-Front: Hoosier 295x30x18 A7 slick with 1" billet spacer
Attachments
Last edited: