Search results for query: *

  1. MaineMustangGT

    Department of Boost GT450 Manifold

    Selling my DOB GT450 manifold. Comes with modified fuel rails, Coolant temp and IAT sensors, heat exchanger pump and fittings, modified alternator harness and few other odds and ends needed to install. Asking $1500 plus shipping from 34953. Sent from my iPhone using Tapatalk
  2. MaineMustangGT

    Engine Harness

    Looking for an engine harness for an 07 GT. Sent from my iPhone using Tapatalk
  3. MaineMustangGT

    Turbo Kit

    Looking for a single or twin turbo kit that keeps P/S and A/C. Thanks Sent from my iPhone using Tapatalk
  4. MaineMustangGT

    4.6 3V Timing Cover

    Used 4.6 3V timing cover. $150 shipped Sent from my iPhone using Tapatalk
  5. MaineMustangGT

    METCO 05-10 3V GT 8 Rib 12% Overdrive Crank Pulley

    METCO 8 rib 12% overdrive crank pulley for 05-10 3V GT. Bought new and used for about 500 miles. More info: http://www.metcomotorsports.com/proddetail.asp?prod=MCP2005 $250 plus shipping from 04412 Sent from my iPhone using Tapatalk
  6. MaineMustangGT

    13/14 GT500 Intercooler Pump

    Selling a 13/14 GT500 Peirburg intercooler pump. Bought it new and used it for about 500 miles. $250 plus shipping from 04401. Sent from my iPhone using Tapatalk
  7. MaineMustangGT

    S&H Stealth Twin Turbo Kit

    Looking for an S&H stealth twin turbo kit for a 05-10 GT. Thanks!!
  8. MaineMustangGT

    WTB Thump Racing Tensioner

    Looking for a Thump Racing belt tensioner. Thanks!! Sent from my iPhone using Tapatalk
  9. MaineMustangGT

    M122 Supercharger

    This is an M122 I had on my DOB setup. I have upgraded to a TVS and no longer need it. Looking to $400 plus shipping from 04401. Sent from my iPhone using Tapatalk
  10. MaineMustangGT

    Valve seals?

    I was freshening up some ported 3v heads I scored, when I noticed the new valve seals I was installing looked different from the ones I was removing. Any one else ran into this? The new seal is on the right. Just want to make sure these are correct before I put the heads on. Thanks!! Sent...
  11. MaineMustangGT

    Wtb: Gt500 mgw

    Looking for a gen 2 MGW for a GT500. Thanks!! Sent from my iPhone using Tapatalk
  12. MaineMustangGT

    WTB: VMP triple pass heat exchanger

    In need a triple pass VMP exchanger. Thanks. Sent from my iPhone using Tapatalk
  13. MaineMustangGT

    Wtb gt500 mgw

    Looking for a gen 2 MGW GT500 shifter. Thanks!! Sent from my iPhone using Tapatalk
  14. MaineMustangGT

    WTB: GT500 Transmission Crossmember

    Looking for a stock or aftermarket GT500 transmission crossmember for TR6060. Thanks Sent from my iPhone using Tapatalk
  15. MaineMustangGT

    Engine Oil?

    What is everyone running for oil in their built and boosted mod motor? Sent from my iPhone using Tapatalk
  16. MaineMustangGT

    WTB 3V Heads

    Looking for a good set of 3v heads. Thanks. Sent from my iPhone using Tapatalk
  17. MaineMustangGT

    WTB: Canton, Moroso, or MMR Oil pan

    Looking for a Canton, Moroso, or MMR oil pan for a 05-10 4.6 Sent from my iPhone using Tapatalk
  18. MaineMustangGT

    Broken Bolt

    So before I packed up my block to send to the machine shop I removed the timing chain rail pins and a bolt that was screwed in the front of the block so they or the block wouldn't get damaged in transit. The two rail pins came right out, but the bolt gave me a hard time and ended up breaking...
  19. MaineMustangGT

    3v heads

    Looking for a cheap pair of usable 3v heads. Thanks Sent from my iPad using Tapatalk
  20. MaineMustangGT

    Torque plates?

    Next step in the engine build process is a trip to the machine shop. The only capable machine shop in Maine has only one torque plate. So my question is, is it necessary to double torque plate an aluminum block when boring and honing? Sent from my iPhone using Tapatalk
  21. MaineMustangGT

    Piston selection.

    Ok, so I had to put my engine build on hold for a bit. But now that the bank account has recovered its time to move forward. The plan is to build a forged stock stroke 3 valve that can handle a TVS down the road. I have cobra/Kellogg crank and Manley rods. Now I just need to select the pistons...
  22. MaineMustangGT

    WTB Forged 03-04 Cobra Crankshaft.

    Looking for a good forged 03-04 cobra crankshaft. Thanks!
  23. MaineMustangGT

    Stroker questions

    Ok, so I got myself a 07 block to start building a forged stroker. I have a few questions. First, what kind of machine work needs to be done to the block? The block is in awesome shape with no scoring at all on the cylinder walls. From what I gather, all I really need is a good hone to run...
  24. MaineMustangGT

    Block value?

    Looking for a 4.6 3 valve block to build a forged stroker. What a good bare block was going for? Thanks
  25. MaineMustangGT

    WTB or Rent Timing Chain Wedge Tool

    Looking to buy or rent a timing chain wedge tool. Tool #303-1175. Thanks

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Sponsor Links

Banner image
Back
Top