Search results for query: *

Yup from my understanding after reading comments on this all day is the factory fan wiring was barely capable of handling the load, after the years the fan/ fan resistor ages and causes more draw on the connections which also gain resistance from oxidation etc. Ive seen mentioned on 05-09's the...

Thanks for the write up, Going through this issue now. Fan works when connected directly to battery, stock relays ok, but factory connections are melted. Im skipping the headache and going straight to this solution with a new fan,connector, and this relay bypass. Have those 30/40a relays held up?

Heres a shot of the coolant pooled under the intake, but check out the oil on pas cam cover. Not sure if this is indication of bad head gasket or cam cover gasket. I let the truck run about 10 min then put the tester on, within a few minutes it turned to a very light greenish yellow. So would...

So friday I picked up a 2000 lariat f150 4x4 with the 5.4 for only $450. I now know why it was so cheap.... I knew the intake leaked and already ordered a cheap replacement from amazon (couldnt find oem intake anywhere online) but once I checked the coolant reservoir I smelled the undeniable...

Yeah.... My 07 vic had same issues as this f150. Intake was leaking,causing several plugs not to fire correctly ...no cel light but the unburnt fuel ended up clogging the cats and had same no power under acceleration issue. This f150 does have leaking intake so im assuming the same thing is...

Just picked up a high mileage 5.4l 2000 F150 4x4 for $450. Was too cheap to turn down, even if I had to replace motor ...I got several other donor fords in my backyard. It starts rough then settles down and idles good. Driving under acceleration is horrible. If i just let it idle around its...

Sorry...just got notification on tapatalk ... Yeah, i bought the trickflow Sent from my LM-G710 using Tapatalk

Only about 1/4oz of pag was discharged. I added 1/4oz to the fill hose but my gauges dont have a purge valve so had to break fitting to purge and most the oil spewed out but i dont think 1/4oz low would cause much issues. Pressures where around 35-40 on low side and 225-250 high. I bet it is...

My 2010 gt's ac was only blowing about 55-60 degrees and its been this way since I bought it. It takes about 15min and having max ac on to just start to get comfortable. So.... I just bought an ac manifold gauge/and vac pump and yesterday replaced the ol ladys accumulator in her crown vic...

well I replaced the coils and plugs.....plugs looked like they were just replaced before I bought it :facepalm: "check before replacing" "not broke dont fix" insert comment here lol :doggy:

I have great lighting in my garage and when I applied it in there it looked fantastic. Once I pulled it outside I could notice the rainbow effect high spots in some areas like rear louvers. Still looks decent. Im going to wait awhile and try to polish it down a bit.

Got the pan in, added the required 5.5 qrts of fluid back and was low 1.5qrts still so the cars trans fluid been low for some time. At least I can keep an eye on it now without ramps,oil gun, and big F-ing mess!

Bought this 2002 E350 with the 6.8l v10 about 3 years ago. It drove bad and timing seemed off. Threw all new sensors in it, cops, plugs, o2's untill finally I had to tear down chain cover to investigate. I found a broken trigger wheel and replaced chains and tensioners while I was in there and...

Had my 2010 gt about a year and its needed paint correction badly. The front and rear bumpers were badly damaged from UV as well. Ive done a full paint correction on the car and repainted bumpers. strip, clay bar, IPA wipe, chip scratch fixes, wetsand, compound cut and DA polish, IPA wipe...

I wondered if anyone retrofit a tube into their stock pan. I already shelled out for the trickflow pan. Have to finish my paint correction and ceramic coating before i get it on ramps though. It never ends [emoji19] lol Sent from my LM-G710 using Tapatalk

Im going to order the cquartz 50ml/100ml reload kit. I planned to strip/polish the car tomorrow but the cquartz wont be here untill next weekend. I wonder if i drove the car after polishing with no sealer untill the cquartz gets here if it will hurt the clearcoat being in the sun for a week...

So I just spent last week repainting bumpers, chip filling, and tomorrow will be doing some wet sanding and compound cutting/polishing to correct paint.... Id like to get a good sealer on after all this work but low on money.... Are the $20-$50 ceramic coating products I see on amazon any good...

Ok guys..... Plans for lowering/upgrading suspension have changed since the funding was needed elsewhere. The popping/rattling noises are getting worse and just need to get them taken care of. I have a $1000 i can spend right now to get this straightened out. I suspect balljoints and/or strut...

Title says it all. Let me know if you have one for sale for a good price... Thanks! Sent from my SM-N910V using Tapatalk

No problem.... i got alot going on too. Let me know if you find it, im still interested Sent from my SM-N910V using Tapatalk

Idk.... im weird and like to put coils and plugs in all the cars i buy used along with fluid changes. It wasnt bad on all the other ford mod vehicles cause i went with the cheap coils. Idk stupid i guess lol Sent from my SM-N910V using Tapatalk

Ok let me know if you find it and want to sell it. I bought a case of RP, an oil gun, filter, and shift solenoids when I first got the car because 1st to second would slip/lagshift sometimes when cold but since ive had the steeda tune it tightened up shifting and havnt had issues. I planned on...

I was checking a while back and thought deep trans pans with dipsticks were not available anymore for 05-10 autos.... but seen this tonight... https://www.summitracing.com/parts/tfs-1012/ Will this fit and clear with my longtube headers? Sent from my SM-N910V using Tapatalk

I ordered ford cops and motorcraft plugs... figured they are due for replacement... thanks guys! Sent from my SM-N910V using Tapatalk

Getting near 90k on my 2010 I bought last year. Havnt had any problems but would like to replace at least the plugs. Ive used cheap cops on multiple ford modular motors in the past with fine results but dont want to cheap out on the mustang. Any decent budget friendly cops you guys would...