Search results for query: *

  • Users: lenko
  • Order by date
  1. lenko

    P0135 Sensor code after new clutch install

    If you look at the wire end of the oxy sensor you see it's metal. When I replaced exhaust system after installing my transmission I pinched the metal and bent it over so it cut into on the wires and car would barely run. Could something like this have happened to cause an intermittent short...
  2. lenko

    Coolant Crossover, Thermostat and Housing, Hoses

    Definitely am old and those are the old parts that came off my old Mustang which I drive almost daily. Sent you an email.
  3. lenko

    Hollow Rattle/Light Knocking Under Car

    Only when driving as the exhaust system heated up and elongated.
  4. lenko

    Hollow Rattle/Light Knocking Under Car

    The hangar arm on my left rear muffler (tailpipe) would touch the back bumper when the pipes heated up so I ground a bit off the arm and haven't heard it since. That was probably 2006 or 2007 shortly after I bought the car new. Exhaust pipes were expanding (getting longer)when they heated up...
  5. lenko

    2005 -2006 Coolant Crossover and Piping

    Coolant Crossover in great shaped removed from my 2006 Mustang GT when a S/C was installed. This has the gaskets and related piping that is under the intake. This is only for a 2005, 2006 GT as there was a change in 2007. Will ship at my cost. $ 200.00 takes it.
  6. lenko

    Coolant Crossover, Thermostat and Housing, Hoses

    $200.00 and I will ship.
  7. lenko

    Coolant Crossover, Thermostat and Housing, Hoses

    I have these off my 2006 if you are still interested.
  8. lenko

    Raxiom Vector V1- pass. side doesn't sequential anymore

    Post # 2 here: https://www.s197forum.com/threads/raxiom-vector-taillight-circuit-board-help-issue.138426/#post-2490436. Working for almost 5ive years since I fixed them.
  9. lenko

    Really need some help

    Pinched Oxy sensor wire shorting? I had a shield around wire bent into the wire and cut it when I reinstalled the exhaust after a transmission replace. Car ran like crap till I discovered and corrected this. This shield is where the wire enters the sensor.
  10. lenko

    Advice on rear end whine

    Look at my post # 18 here: https://www.s197forum.com/threads/gear-pattern.151455/#post-2577142
  11. lenko

    Looking for part

    That's what I thought. Even the Saleen ones differ for 2007.
  12. lenko

    Looking for part

    I've got one off my 06. Don't know if its same for your 07 as that looks different. You can check it out and if it works I'd sell it.
  13. lenko

    Gear pattern

    One thing I will admit, 373s are harder to set up then 410s. When I first tried 373 in my Mustang, they whined, but the 410s I did later I used the MHD method to get the correct pinion size worked. If you look at the first photo above, the pattern is near the toe nice and oval and consider to be...
  14. lenko

    Gear pattern

    I always use the MHD Master Housing Dimension method and follow this guide. You can get the precise pinion shim size and end up with quiet gears...
  15. lenko

    Possible Coolant Leak

    https://mustangforums.com/forum/4-6l-v8-technical-discussions/737032-sneaky-coolant-leak-fixed.html
  16. lenko

    SPR cams and tuning. 07 GT

    Brenspeed did mine for the Comps 123000 VSR probably 10 years ago - still strong and run great. Installed them myself and they adjusted my previous tune for them by a sent file.
  17. lenko

    ISO coolant crossover pipe

    deleted
  18. lenko

    raxiom vector taillight circuit board help issue.

  19. lenko

    2006 GT Water Crossover Gasket fitting Kit

    Always an option.
  20. lenko

    2006 GT Water Crossover Gasket fitting Kit

    You don't need sealant with the Crossover for the Saleen. The rubber or neoprene gaskets fit into a grove and extrude out a bit to seal to engine block. At least that's how mine fit when I installed the Saleen VI super charger. This is the crossover I had to replace with the one for the Saleen...
  21. lenko

    ISO coolant crossover pipe

    If you still need it, I have one. Like new c/w gaskets. From my 2006 GT. Also the coolant tubing under the intake.
  22. lenko

    Exhast drone help

    Not suggesting you do this but this eliminated my drone completely and the sound is amazing. Ends of the add ons are blocked completely. Approx. 24 inches of quarter wave sound disruptors.
  23. lenko

    raxiom vector taillight circuit board help issue.

    Mine are the version1 I guess because they have the red reflectors and backup light on the bottom as my signature on the left. When I took mine apart, there is a little box inside that has the electronic board and it was there that I found the diode sticking up. I soldered it down and a month...
  24. lenko

    Interesting Noise at Idle

    Had similar noise so a couple of months ago replaced Phaser and solenoid on the passenger side and noise is gone. MELLING MEL VCTA- 1000 Variable Valve Timing (VVT) Sprocket States MELLING MEL VCTS- 1000 Variable Valve Timing (VVT) Solenoid / Actuator
  25. lenko

    Old SCT tuner advice needed

    Still using my SCT X Cal 2 tuner that I bought in 2006. One time it stopped working so I took it apart and spotted a broken wire and soldered t. Works like a charm. Kept all my various tunes and loading programs on a separate hard drive in case I ever need them. Never did find need to update...

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top