Search results for query: *

  1. J

    Supercharger Inlet/Outlet Hoses

    An Aeroforce Interceptor. The sensor taking the reading is on the drivers side of the intake manifold. Does your setup involved drilling into the intake manifold in another location?
  2. J

    Supercharger Inlet/Outlet Hoses

    I do indeed have a bypass installed. 90 degree fitting at entry of the degas tank, 45 degree fitting at the exit. 1" tubing everywhere except the inlet/outlet of the intake manifold, to/from the degas tank, and to/from the CWA100 pump. Could the reason for the low activity in the degas tank...
  3. J

    Supercharger Inlet/Outlet Hoses

    Hello everyone. Just finished installing the CWA100 and all silicone hoses and noticed when running it up to temp that the inlet was and seemed to have great flow but the outlet hose was noticeably softer. The outlet is flowing because when I squeezed it the Degas take gurgled a little. Could...
  4. J

    Can't Fit 3 Fuse Taps In SJB

    Hello everyone. Just curious, is there an alternative to a third fuse tap in the SJB? I'm looking to provide constant power to the newly installed dash cam but don't seem to have the space. One fuse tap provides switched power to the Aeroforce Interceptor, the other to the dash cam. Need...
  5. J

    VMP Dual Outlet Heat Exchanger

    I found it by accident. Just curious how it will be of benefit. Routing and merging the two outlets is going to be a challenge.
  6. J

    VMP Dual Outlet Heat Exchanger

    Researching heat exchangers, I see that VMP dual outlet heat exchanger for sale. Never seen a dual outlet before, what is the advantage over a single outlet? I'm guessing it improves efficiency but what do you guys think? I've written to VMP but they haven't gotten back to me yet.
  7. J

    Is it possible to....

    Hello everyone! Is it possible to open up the inlet and outlet on the back of the Roush Intake Manifold? VMP sells an upgraded intercooler brick but getting that seems pointless if the inlet/outlet passages are still at barely 1/2".
  8. J

    Roush Intercooler Brick

    Thanks for the quick reply but I already have their Super Single, the GT500 pump, and 1” lines. Last piece of the puzzle is the intercooler brick with its 3/4” inlet and outlets (which are apparently only 5/8”).
  9. J

    Roush Intercooler Brick

    Hello everyone. Just wondering if there was an upgrade for the intercooler brick that comes with the Roush TVS supercharger. My car is an ‘05. VMP sells one that will fit 08-10 model years but was told that it won’t fit mine. Are there any other options out there for me? Thanks In...
  10. J

    Intercooler Pump Issues

    Jason did get back to me saying "I'll have to figure it out." He needs to realize that not everyone knows as much about this stuff as he does and shouldn't get offended when people that don't know a lot about this stuff ask questions.
  11. J

    Intercooler Pump Issues

    It works outside the car. Inside all wired up is another story. Does that indicate a bad ground?
  12. J

    Intercooler Pump Issues

    I saw very post. Helpful but it doesn’t completely solve the issue. Pump works just as it should when I test it outside the car. For some reason, it doesn’t want to turn on when I put the battery and harness back in.
  13. J

    Intercooler Pump Issues

    I did reach out to the manufacturer but he hasn't gotten back to me yet. When I had everything installed in the car (power to lug at fuse box, ground to passenger side strut tower, trigger to rf noise suppressor), the pump wouldn't run at all even though I'm getting power at both the fuse box...
  14. J

    Intercooler Pump Issues

    Reversed the polarity? I don’t see how that is possible as I was very careful to not do that.
  15. J

    Intercooler Pump Issues

    Just completed the bench testing of my D.O.B Powa Pump. What is happening is very strange. I took the battery out of the trunk. Put the power wire and the trigger wire on the positive post at the same time and the negative to the negative post. Pump runs. However, when I pull the trigger wire...
  16. J

    Metal Coolant Tubes On The Roush TVS

    Hello everyone. Can't seem to find installation instructions for the Roush TVS, specifically the unit for the 2005-2009 Mustang GT. I'm going with 1" lines and need to remove the metal coolant tubes that run alongside the passenger side valve cover. How many different places is it attached?
  17. J

    Department Of Boost Powa Pump Install

    That was the first thing I did. Jason hasn't gotten back to me as of yet. Thought someone here could help with the wiring harness. Heat exchanger and pump are in place, need guidance on the wiring said.
  18. J

    Department Of Boost Powa Pump Install

    Looked there first. Nothing detailing the Powa Pump install.
  19. J

    Department Of Boost Powa Pump Install

    Tried that first. No results.
  20. J

    Department Of Boost Powa Pump Install

    Hello everyone. Seeking advice on how to install the Department Of Boost Powa Pump, specifically the included wiring harness. No instructions came with the kit. I removed the GT500 intercooler pump that was in the car then wondered what to do with the connectors from that harness. Any...
  21. J

    Anyone replace a the positive side battery cable? 05 GT

    I'm in the process of doing this myself. Your post was a big help. One question though, where did you ground the starter?
  22. J

    Stalling On Cold Start After Winter Storage

    I have an Aeroforce Interceptor gauge and just realized that it can read cylinder head temps. Correct me if I'm wrong but if I am getting a reading that means the ect is working properly right?
  23. J

    Stalling On Cold Start After Winter Storage

    The battery was actually out of the car on a little stand I made to keep it off the cold floor, was doing headers and other things. I have an old X3 handheld, can I use that to adjust the idle? Its concerning that the radiator fan is not coming on which Dino thinks indicates a bad ect sensor...
  24. J

    Stalling On Cold Start After Winter Storage

    Thank you for the quick reply Dino. The act sensor is located under the intake manifold, correct?
  25. J

    Stalling On Cold Start After Winter Storage

    Hello everyone. Need help diagnosing a problem. I did indeed do a brief search but didn't find anything that resembled what I am seeing. Took the car out of winter storage and on a cold start, the engine revs to about 1000 then drops to 500. It will eventually stall if I don't apply some...

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top