Search results for query: *

  1. pass1over

    Leather Seat Covers

    pretty sure that's where I bought the seat cover for my car as well, same vendor. I've been super pleased with it. Had them in the car for over 3 years and they still look like the day I put them in. I did the driver side only and you can't tell the difference between them in the car. Color...
  2. pass1over

    C1A99:17-8B-Brake Pressure Sensor Replacement

    also, when I fixed my C1A99:17:8B code, I replaced the HCU for the ABS module, did not mess with the sensor in the ABS module. No brake fluid mess at all.
  3. pass1over

    C1A99:17-8B-Brake Pressure Sensor Replacement

    Did this 3 years ago. No expensive scan tool is required. Forscan does it and I believe it's still free.
  4. pass1over

    sway bars, rear and wheel spacers

    because you don't
  5. pass1over

    sway bars, rear and wheel spacers

    I've replaced my inner's and never saw any limiters in there. New inner's didn't come with any, and I didn't install any.
  6. pass1over

    sway bars, rear and wheel spacers

    I went from 18's to 20's on my car like 10 years ago and never changed/added these. No rubbing at full lock either. I saw these and always wondered, but never messed with it because I didn't experience an issue.
  7. pass1over

    add powered sub?

    There is zero room behind the back seats in the Silverado. Enough to mount an amp, but that's it. The rear seat is basically on the back of the cab. I use the under seat storage on the drivers side pretty often. I don't think I can fit another sub box under that side without losing the...
  8. pass1over

    add powered sub?

    Not my mustang, but the Silverado that I have. I have a single 10 sub under the back seat with an amp hooked to it. I don't want to add another sub under the other side and lose all under seat storage. I can however fit a 8" powered sub in the center console. I was going to use an RCA "Y" for...
  9. pass1over

    Brake pressure sensor

    correct
  10. pass1over

    How Ya'll doing from NE Ga USA

    almost 239k on my '12 GT
  11. pass1over

    Bambi mode lights

    In my experience with Forscan, it's not that easy. I hope I'm wrong for his sake though. Everything I've seen, and worked with is like hex codes. Like 727-01-01 B828 01F1 0002 727-01-02 8901 0000 00BB 727-01-03 0000 0000 0032 There will be huge columns and pages like this. The 3 right...
  12. pass1over

    Bambi mode lights

    There probably is a way to activate or deactivate that feature using Forscan. However, there's way more info out there on the F150 ecu than the mustang one.
  13. pass1over

    Anyone used these aftermarket seat covers?

    sounds like you found some covers, but just in case ... The seller is seatcoverreplacement The auction title is .... 2010 2011 2013 2014 Ford Mustang GT Convertible Couple Black LEATHER Seat Covers I can't post a link as I'm on my work computer and ebay is not allowed.
  14. pass1over

    Anyone used these aftermarket seat covers?

    Yea, I can't tell the difference at all between them. Stitching, perforations, etc., it's all identical.
  15. pass1over

    Anyone used these aftermarket seat covers?

    I look at Katskins and couldn't find anyone that would just sell me the covers. They want to install them as well.
  16. pass1over

    Anyone used these aftermarket seat covers?

    Purchased a drivers seat cover off Ebay December 2022. Don't know if it's the same brand/seller though. It matches my passenger seat almost spot on, can't tell the difference. It's help up well, almost 3 years now. Car is my DD, I've put almost 53k miles on the car since I've put the cover...
  17. pass1over

    Allowed front tire / rear tire diameter difference

    2012 GT, Calimer MT82, 3.73 gears, brembo fronts, shelby rotor upgraded rears, forgestar CF5 wheels (20x9 and 20x10.5) It's a premium, only options were HIDs and the gear.
  18. pass1over

    Allowed front tire / rear tire diameter difference

    I would get them as close to possible for aesthetic reasons as well. It would look weird for the front sidewall to be taller than the rear. You can get away with a thicker/taller sidewall on the back compared to the front, but too much of a difference would look a little odd on that setup as...
  19. pass1over

    Allowed front tire / rear tire diameter difference

    I currently have 265/35/20 fronts and 305/35/20 rears. This is a 4% difference, I notice nothing wrong with driving my car. Before that, I had 255/35/20 fronts, which is a 5.2% difference. Again, no issues, for 60k+ miles on that set. I've got almost 250k on my car with basically that tire...
  20. pass1over

    Tires

    just replaced the 555 g2's on the front of my car. They started wearing weird (inside AND outside on passenger side, just inside on drivers side). Pressure was always kept 40+ and alignment was in spec, I have it checked every 6-8 months. I can't complain too much as I got 61,000 miles out of...
  21. pass1over

    Is a remap necessary when engine swapping 05 to 09

    do you have a bi-directional scanner that you can watch the data stream while the car is running? Might get you closer to what the problem is.
  22. pass1over

    Spark Plugs

    Never heard any of that before. Most/all new spark plugs have a nickel, or similar coating on the threads which prevents galling and corrosion. Anti-seize is not necessary
  23. pass1over

    Driveshaft

    mythbusters busted this myth like 20 years ago. I still run and suggest a safety loop, as it will prevent a lot of damage to the car while its flailing around under there, and it will probably end up in your trunk area, but it won't catapult your car.
  24. pass1over

    Strange Ford 9"

    you can modify an 8.8 to handle over 1000 hp, and it's completely bolt in, because it's designed for the car. Brace the housing, weld the tubes and run 31+ spline axles. If you already have a housing, this is the cheapest way to go. As far as being narrowed, your housing width will depend on...
  25. pass1over

    2011 Mustang GT Window Issue

    reviving this guy's thread as I'm having the same issue. I replaced my drivers side regulator with a dorman unit. Everything is tight, but there's play in the window and it causes a rattle. Are there any other adjustment/tightening points on them?

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top