Search results for query: *

For sale is my 2006 Mustang GT Premium 5 Speed. Bought her 5 years ago at 18k miles and she's served me well over the years but I don't really need two vehicles so off she goes to someone who will enjoy her. Always garage kept, great condition. Paint is a 9/10 and interior is an 8/10. Fresh...

Looking for a Steeda Oil Separator for the 05-14 years...Just like the one below: http://www.steeda.com/steeda-mustang-oil-separator-555-3711/

Because of this... And this... And let's not forget this Long story short....It's bumper to bumper traffic at 5pm on Friday in Socal. I had an opening to switch lanes, blinker on for three flashes before making a change around 5mph....and BAM, this crotch rocket skates...

Lock it up, found one.

I'm looking into picking up a new MGW for my 06 and had some questions in regard to the shift boot. I was going to order one from a mustang rocks leather but it seems they've closed their doors. When I spoke with them they mentioned that they can make the leather a little shorter due to the...

I finally had a weekend open to do some paint correction and apply the SPNS that's been sitting in my detail cabinet since christmas. Pics will come, I didn't have the lighting last night to take any and since it rained today I have a better idea of the water beading capabilities. Step 1...

I've been trying to figure out some gremlins on my car since I installed my JBA headers and O/R H. Initially was getting codes showing that my passenger 02 sensor was running rich, but after tune revisions and datalogging that went away and the car seemed to run fine for a while. More recently...

It's nearly time to go tire shopping. I'm a bit surprised that my Falkens have only given me about 25k-30k miles but I'm used to 45-50k tread life from my old Tahoe. Anyway, I've got a set of FK 452's sized275/35/R19's on my SVE Drifts right now and leaning towards the Continental DW's based...

Clean off. This is the wire grounded to the bolt on the engine perch, passenger side near the starter. How badly am I screwed on this? Is the car even drivable right now?

For those of you who have read I've been chasing down issues ever since my LT's went on a couple months ago. Right now I get an occasional cold hard start. I'll fire up the motor and it will immediately die, unless I keep the revs up; for the first 5-10 seconds the engine sputters and fights...

Primarily looking for a bassani axleback but will consider the other options as shown in the title. I switched from SLP's to Bullitt mufflers after my long tube install but am looking for a different sound.

I just saw that CG revealed their new Torq buffer at Sema, has anyone else been looking at this as well? Judging on price point alone I think this is a Griots/PC XP7424 competitor and not a Flex/Rupes fighter. What are your thoughts...

It's been about a week since I've had my JBA Headers and O/R H on....and I've had some small troubles and finally started getting codes thrown today. I've had an intermittent low idle from between 500-700 while decelerating and idling at a stop. A few times the idle dips very low to about...

SOLD!!!

Just finished the JBA install finally! As soon as i began my road test after being deafened by my new lack of cats, i released the e-brake and felt something click. I began to reverse back but it felt like something was catching. Sure as shit, as soon as I made it out of my neighborhood I...

I've been doing a search for this all morning since I inadvertently ripped mine a while back and decided I needed to replace it. I've only been able to find the part on ebay thus far for like $14. There's gotta be a better price on this somewhere as it's just a piece of rubber...anybody know...

I had to push the install of my JBA LT's to a different weekend. After doing some more research and whatnot I began to question whether or not this header would be able to seat with a stock gasket against the block. Does this look like I need to machine it flat? I really don't want to get to...

I'm about halfway into my header install, everything seems to be going fine until I start removing the studs. The ARP fasteners that I was recommended from JBA were this set here: http://www.summitracing.com/parts/arp-400-1210?seid=srese1&gclid=CLO2vKOsib4CFVKIfgodsy4ATg As I start taking out...

About to install JBA LT's and an O/R H pipe and I'm 99% sure that my SLP Loudmouths aren't going to cut it anymore on my setup. Looking for something along the lines of Magnapacks, Stingers, etc or perhaps another setup if the sound can be determined as "good" for the setup. I just need...

I was bored today and decided to try and hunt down some gremlins that have been bugging me. Every time I push the clutch in and let it out I get a squeaking sound and it drives me up the fucking wall. I went under the dash to try and isolate exactly where the sound is coming from. After...

Just a heads up, Autogeek is having a sale for the next 12 hours or so on all paint coatings. I was going to try Bouncer's Sherbert Fizz since I got their VIP special email but now I might get this cQuartz UK kit below for $49.99: http://www.autogeek.net/cquartz-uk-edition.html 30 ml...

My JBA LT's are off getting ceramic coated so I'm prepping for the install. I've purchased JBA O/R H and defoulers along with 4 02 extensions and ARP locking header bolts. My question now comes down to the gaskets. I've seen many threads which recommend using OEM gaskets, some people even...

Looking for a set of Prothane motor mounts for an 06 Mustang GT. New or used, I just would like to upgrade these when I'm under the car swapping headers.

Title pretty much says it all. I was my 2006 Mustangs third owner and picked her up in April of 2011. Coming from the Chevy Tahoe I had, this car was great and it was nice being able to drive something that didn't handle like a brick on wheels. I went about throwing various appearance and...

SOLD! Lock it up.