Search results for query: *

Coulda sworn ive seen this topic before, but searching the code came up empty. EDIT: I swapped 0 and 1, code is P0133 LOL O2s were replaced over a year ago, MAF 8 months ago, all wiring inspected when MAF got swapped. CEL popped while cruising on the highway. AF ratios were fine the entire...

I've been sitting on some upgrade parts for a few months and need to get things going again. I need to install the bigger injectors but have never done them, can't find a "good" tutorial on YouTube, and my usual shop wants $500 to do them. Ill tackle it myself for that price. Is there anything...

I know there’s probably a thread on this already somewhere, but I searched and didn’t find one. Output shaft seal on my trans has been leaking for quite a while. It ain’t TOO bad, one or two drops every few days. Sometimes it looks like it doesn’t leak at all (tshirt on the garage floor). But I...

If this should be in the “Wheel and Tire” section, I apologize. Asking here because the corner carvers might better understand what I need I’m looking for opinions on a tire with more straight line traction than what I run now. I have been running Falken Azenis 615k+ since 2015, 295/40-18...

After adding a few horsepower and a lot more boost on the way, I need to start thinking about a transmission upgrade. Built engine and driveline sandwiching a stock trans with 75000 miles isn’t going to end well. Obvious swap is the Magnum, but I don’t really NEED that 6th gear. It is pretty...

Got my car retuned today after a couple upgrades, but hard to say how much I’ve actually gained. The car was always tuned on a Mustang Dyno, today it was done on DynoJet. Shop owner told me beforehand his dyno is a heartbreaker, people get higher numbers everywhere else. Gonna do this as a list...

I finally got this gauge installed and now that the numbers are in front of my face, I’m not sure if everything is as it should be. At idle, it’s reading 14.7 but jumps back and forth between that and low/mid 15s, kinda lean. At cruise (65-80mph), it’s the same thing except it’ll jump as high as...

Looking for a new belt, tried searching the part number and Google comes up empty. Dayco belt, has two numbers on it: 1247K6 and 20-9770. Don’t necessarily need to get another Dayco, but need to know the length of the belt. I’d just cut it and measure if I had a spare. Looking at the Dayco...

Shop has had my car a couple weeks for few parts, including a fuel pump which is the last item to get done. Swapped in a DW400 for the stock pump, no changes to any other parts on the pump assembly. They called me on Friday and said the pump is in and car is “ready”, but the gas gauge isn’t...

I’ve got my car at a local shop getting the radiator, heat exchanger, and UCA swapped out. Maybe a few hours of work. They’ve had the car since June 19th and it still isn’t done. They’re local, do some pretty insane builds, and have a good tuner but they’re obviously SLOW!! Maintenance on...

As the title states, looking for a deal on a dual pump setup for my ‘10. Must be new, unused, and complete M-9407-MSVTA Or M-9407-GT05

Looking to add some boost while my car is getting it’s other upgrades done, but I’ll need more fuel. This FRPP kit M-9407-GT05 will fit and work but will result in a faulty fuel level reading. I can’t seem to find a part number for the ‘10. Maybe there isn’t one Anyone know how the fuel reading...

Wasn’t sure where to post this, so sorry if this is the wrong spot. Who’s in Texas and what shops do you trust to work on your car? I am looking for recommendations for speed shops in Central Texas. Dallas/Ft Worth isnt too far a drive, but Houston is a haul. Really looking for personal...

Haven’t been here in an while so quick recap. I’ve got a 2010 GT with a slightly built 4.6 and a Kenne Bell. Anyone with this combo (or similar) knows heat is enemy #1. The the Kenne Bell IC expansion tank is garbage. It gets hot, it warps, and the cap leaks. So im replacing it with a factory...

Tl;dr- I need a cai and MAF setup for my 2010 with Kenne Bell. KB no longer makes the parts I need. Full story: Just had a new engine built and after break-in put a smaller pulley on. Should be around 12-12.5 lbs boost. Was only able to get 9.5. The tuner says the culprit is the KB carb legal...

Haven’t been here for a long while! My question is more opinion than tech, so hope this is the right section I recently added a Bassani O/R xpipe and am looking for axle backs that would pair well. I currently have Pype Bombs, and while it’s sounds amazing wide open, it’s just not practical...

Hey all, longshot here,, I am going to 18x10 all around but the wheels I need are no longer sold by AM. I’d like to find two of them as I already have two on the rear. Here is the link https://www.americanmuscle.com/charcoal-trackpack-wheels-1014.html Please no recommendations for others. I...

Anybody home? Sent a couple messages through "contact us". I need help placing an order from overseas, but shipping the parts stateside.

I see in the corner carver forum that guys are using this-or-that spring f/r combo (rates). Where can I find/buy springs at desired rates? Is it simply a search of all brands to find who has what I want? Hope there isn't a post on this already, I tried searching.

This place is overflowing with anything you can think of. Porsche and AMG are like Toyota in the states. Not a day goes by without seeing a handful of Ferraris and a Lambo or two, and starting to see more McLarens. Aston Martin, Bentley, Maserati... the shit is ridiculous. I don't normally snap...

Im moving, if anyone needs this stuff ill let you have it cheap. Im not hipping anything, but ill drive a little to meet up. Lets say $1 a piece for the technicality. (FREE!!!!) mustangbackseats by Kenneth Stephens, on Flickr interiortrim by Kenneth Stephens, on Flickr interiottrim2 by...

First time on a prepped track. Prep didn't mean shit, as these 555r's are done for. 60ft time tells the tale. At east it was consistent over a dozen passes. Time slip by Kenneth Stephens, on Flickr https://www.youtube.com/watch?v=EM_EL3llJc0

I am going to have approx $16k to dump into my car in a couple weeks(months? LOL). The problem is, it needs everything LOL. Motor (new or rebuild mine), suspension, trans, brakes, clutch/flywheel,,,, you get the idea. Can it be done? Goals are 600hp/600ft lbs on corn, daily driven, but will...

I have got to figure out how to get the power down. Slipping the clutch through 1st, grab 2nd and its blows 'em off. It snot even that much power. Anyway, this was fun. Didn't think the dude would go, he got the jump on me. Just a quick 0-85. Disclaimer: this is stupid and I rarely do...

Came off my '10 and has been stored in controlled climate (bedroom closet) since. Not sure what years it fits, guessing 05-10. Not even sure what to ask for it, if you need it, PM me to discuss. Factory Intake by Kenneth Stephens, on Flickr Factory Intake Top by Kenneth Stephens, on Flickr...