Search results for query: *

I'm looking for a Tremec 6060 that is in good shape. I would also be interested in associated parts for an 05 - 10 3650 to 6060 swap. Thanks!

I have for sale One set of JBA Axle-back exhaust for 2005-2009 Mustang GT. They are in great shape and have only been on the car for 2,000 miles. I went with straight through style muffler for better turbo response. $225 shipped One set (LH and RH) cams for 3V (Originally off of my 06...

I took my car to Gateway Friday night. Its a 281CID 70mm single turboed manual trans, full weight car on MT ET Street Radial (265/40 18s). I ran it on 93 octane. I ran 15PSI boost, 13 degrees timing and 10.9 AFR. My best run was launching with 2 step at 3400rpm. I still bogged with 60ft at...

At 11psi of boost AFR stays at a steady commanded 11.3 during WOT runs. When I gave my manual boost controller a twist I got 14psi of boost, but it went lean (about 12.7). I went home and adjusted the MAF Transfer function where needed and went out for another test run. It still went to 12.7...

I am looking for a set of 3V BBR stage 2 cams. Thanks

Looking for a set of BBR stage 2 cams for 3v

Please help! I am running out of fuel with the Ford Racing Dual Pump system. My car is a single turbo car. At 7 psi, all is well, pressure is 38-40, AF steady 11.4-11.5, MAF at 3.4 volts or so, pump duty cycle is a little over 80%. At 11psi I start to loose it. pressure is around 36, AF OK, but...

I have a set of custom 3V turbo cams that are ground by Comp. The specs are: Duration at .050 226 Int 231 Exh Lift 501 int 476 exh lobe sep angle 115.5 These cams make great power, spool my turbo quickly, and have a mild but noticeable idle. They are still in the car, so I would need to take...

Does anyone know what parameters to look at when it come to tuning acceleration enrichment? My car bucks and jumps a little on tip in an wide bands goes to 18+ or so AF for a second. I am wondering if acceleration enrichment could be the issue. I tune using Delta Force software. The car is...

This may have been answered 100 times before, but I can't find it searching. I am building my 2006 3V engine. WAP block, H beam rods, Saleen CP pistons, and an 8 bolt nodular iron stock crank. I plan on running in the low 500 rwhp range most of the time, but will occasionally turn up the wick on...

WTB BA-5000, PMAS, or Pro-M slot style meter

I am selling my Abaco DBX. Made great power and driveability was excellent on my 2006 single turbo 3V. You get the meter and the harness for 2005-2010 GT. $175 Shippped

Ok So I have been troubled for some time because my car would blow blue smoke out the exhaust (so I thought) after I would let of the throttle following a hard (3/4 throttle or more) pull. I figured it was pulling oil through the turbo seal or a PCV issue or at worst, bad rings. Well I finally...

I just want to say thanks to all of you for your input and guidance throughout my project. I finished my car just in time to get it tuned and take it to the track before I head to Afghanistan. It put down 570 rwhp and 559 rwtq with 11psi, 15 total timing, and mid 11s on a/f. I went to the track...

My Predator broke and I have a custom tune in my car. How do I upload a new custom tune with a new Predator since the original backup is not in the car?

I think I finally have the bugs worked out of my build and I am heading to the dyno for tuning tomorrow and to Gateway international on Tues. I am running a set of 265/4018 Mickey Thompson ET Street radials and was just curious what tire pressure some of you are running with similar tires.

Fixed my engine temp sensor and overheating issues today and drove my car for the first time for more than a mile since the build. Rear end is stock with a girdle, tranny is a promotion 3650, spec stage 3 w/ aluminum fidanza fw, and a steel axle exchange ds. something in the drive line whines on...

Got my built stroked turboed 3V up and running, but I don't have a good tune for it yet and I am just driving it around real nice to get the clutch broke in. So far I have only drove it a mile or two down the road and runs pretty good. In these very short(5 min) driving stints I noticed that the...

I finally got my car together and took it for a drive today. All is well except that my temp guage isn't working. Is the sensor for that the one that is in the drivers side of the block with the heavy orange wire? I need to look at my old block and see if a rod didn't go through that area of the...

I disconnected my o2 sensors when I pulled my engine and it has been so long that I need help with reconnecting them. The green wired ones are the front and the white are rear, correct? Now as for the front ones, how do I know what wire goes to what sensor (I know green to green and white to...

I finally got my car fired up last night, but I have a problem. It is still up on jack stands with the tires off right now, and when it is running and in neutral the axles spin when I let out on the clutch. The tranny is a 3650 from promotion. The shifter is in neutral, and it feels like it is...

I have had issues trying to get my new engine running, but I know what the deal is now, so I needed to take the turbo off to get to the timing chain cover. Anyway, as I took the oil feed line off the turbo, it was bone dry, so i took off the oil filter and it was dry too. I have cranked on it...

I topped everything off, plugged everything in but fuel and spark, let it turn over for a few seconds, plugged in fuel and spark, crossed fingers and attempted to start it up. It fired lightly and kind of hiccuped for about three seconds then died. I tried again and nothing. It will not fire, it...

I am finishing my project tomorrow and have a few questions. My old combo was a completely stock 3v with a 60mm single turbo (39 lb injectors), minus axle back and an electric water pump. The new combo is a new aluminum block with a 298 ci Livernois stoker kit, MMR sage 2 heads, MMR custom stage...

I have a brand new in box Spec Stage 3 (26 spline, not 10) for an 05-07 Mustang GT with an upgraded 26 spline input shaft. I paid $350 plus shipping. I will let it go for 300 shipped. PM or call 217 821 6499 if intrested. Zach