Search results for query: *

So i either cracked the elbow, which i'd expect it to leak all the time or i got a piece of sand in there causing the oring not to seal completely. I suppose the elbow is deforming some when it gets hot is also a possibility. I could have damaged the o-ring too. Ford doesn't sell just the elbow...

No street racing here, just two muscle cars accelerating to the speed limit at the same time and in the same place.

Looking for opinions of the quality/fitment.

Since my battery is in the trunk now it seemed silly to have some 20 feet of wire running from the fpdms all the way to the fuse box under the hood. So I ran it directly to the battery. This has to reduce voltage drop to the fuel pumps right? This is the dual gt500 pumps that came with the...

For those with oil pressure gauges what psi do you see at idle when hot? I'm getting 36psi even after driving it to get the oil hot.

My spec 3+ is starting to act funny. engagement point seems to be moving and it just feels different. Haven't notice it slipping, but i rarely get to give it full throttle in 4th gear. It probably has 30k miles on it and a few hard launches at the track. i may have rode it a few times in second...

Seems the days of being able to buy a built 3v short block are long gone. Is any reputable places still stocking these? I feel like i can do all the assembly except the bottom end, so i'd much rather buy a short block that's been assembled by a professional.

Has anyone used resistors to fool the computer when removing the evap canister system for the gas tank? I did with with great success for my airbags, even the seat belt sensor. They all took a 2.2 omh 1/2 watt resistor. i tried ohming out the valve in the engine compartment and got 3.7ohm. I'm...

I went to weigh the 06 gt today. 3/4 of a tank of gas. It's a little heavier than i thought it'd be. About the only thing i haven't done to reduce weight is the k member. AC is gone, rear seats completely gone, stock seats replaced with corbeau, 1 piece drive shaft, tubular radiator support. I...

I don't know why this is so hard to find. i need a 1/2 inch id hose that can handle 22-24 hg of vacuum without collapsing. i ordered this because it said pcv and it's mishmoto branded, like that really matters. I didn't read the reviews and some say it collapses. i had been using a ghetto setup...

So the shorty headers put out more heat and the stock fuel line running to the fuel rail runs right over top of it a few inches above. This line seems like a hard plastic? I was looking online and saw this on ebay and another sold by edlebrock for even less. I'm worried about the stock line...

So maybe it's not so obvious in the video. The engine noise and ehaust is drowning it out some, but it lasts for about 25 seconds and starts a couple of seconds after a cold start. it is even more obvious with the hood closed. So what are my options? i can't tighten the bolts anymore, shit is...

These things are kicking my butt. all the upper nuts/studs broke free with little effort and some pb blaster, but the lowers are fighting me. i'm afraid i'm going to break one. going to try tightening all the uppers back and see if that helps loosen the lowers. Any tips would be much...

I have not actually timed it, but it is a good 10 seconds between pops i'd say. It might just be random and not rythmic. it really sounds like expansion of the exhaust, but it's at operating temp. It also seems to make more popping sounds when it's off and cooling. maybe i bound up the...

It's a hood vent from a 2014-17 camaro z28. I kid you not! Looks better on the mustang imo. Had to cut the rear most vent to clear the whipple, no biggie, the vent was $49 on amazon. I used strips of aluminum from Lowes to sandwich it to the roof. Not the prettiest solution, but it...

I never really considered a rear seat delete kit because they all seemed kinda heavy and expensive for what they were. I had to take out my rear seats to install the corbeau harness so i decided to make the lightest possible delete i could think of and remove everything possible including the...

Does anyone know what paint would match my 06 gt door panels? I glued the inserts back in with 3m spray adhesive and being lazy I didn't remove the overspray right away. I tried removing it with wd40, goo-gone and a green scrub sponge and failed miserably. Now i'd like to cover up my screw up...

Really considering this since my hoods paint is failing in spots from corrosion. Looking at this one specifically for the cutout. my whipple pulley is fairly close to the hood. this would probably place it further forward than typically seen. I'll try wrapping the hood in some of that new...

Things you'll need. 1. 13 feet of 1awg + battery cable, 2 feet of 1awg - battery cable, some sort of distribution block to connect your positive cables in the engine bay, copper crimp on battery lugs(order 6awg if reusing stock wires, the 4awg are way too big for some reason, chinese tolerances...