Search results for query: *

The battery drained completely, and I had to open the door with the window fully shut. I've tried the window reset procedure a few times. Press and hold down, once the window is down, continue to hold down 2-5 seconds then press up and once the window is up, continue to hold up 2-5 seconds...

2005 Mustang GT 151k Earlier in the week, I noticed my rear driver side brake squeaking when braking or turning left. I first check the tightness of the lug nuts, they were torqued to 100 ft-lbs. I then took the wheel off and took off the brake caliper to check the pins to see if they were...

I am looking to buy the manual linkage bar or buy a shifter with the linkage bar for my 2005 Mustang gt . Any help would be appreciated

When going over at bump in the road it sounds and feels like something is hitting my MGW shifter. At first I thought it was something in the trunk moving around. The shifter doesn’t have any up and down play. The driveshaft doesn’t looking like it is hitting the shifter linkage. I check...

I have a 2005 GT with 138k miles. I just replace the all the Shocks, Struts, End links, Inner Tie rods, Tie rod ends, and Wheel Hubs. I hear a popping noise during hard left turns or sharp turns from a stop. I did hear the noise during harp turns from a stop before I replaced everything but...

it start 3 week ago with a stumble at 80 for a second. Over time it has gotten worst to the point where it was happening all the time plus there a noise in the timing chain area (at the time i thought it was my stock tob going) when decelerating and now when revving down. I got a P0345 and...

Do I need to replace or should replace the valve cover gaskets when swapping valve cover for coated ones?

I am looking for Charcoal Black Interior Seat Cushion Valance part number 62186B. my will not attach to the seat any more. Also does any know how to take off the Recliner Adjustment Handle?

I was trying to put on my winter tires and as I was taking off a lug nut I noticed it was just spinning. The whole stud is spinning and I can't tighten or loosen it. i tried getting some lock pliers and pulling on it but it doesn't do anything. so no the lug nut is just sitting there on...

What: WCS All Make & Model Carshow Where: Bahmama Breeze 406 E. Golf Road Schaumburg, IL 60173 (map) When: Sunday August 14th 2011 10am-3pm (Registration til 1pm) Who: Everyone Cost: $10 per entered car, spectators FREE To download a printable flyer clickhere This is the Second show this...

GT500 Throttle Body w/electronics also coupler and clamp. The holes of the the tb have been drilled out to allow it to directly bolt up to the stock intake. $150 shipped

I am not sure if I should even be worried about this but I have been having cooling issues since my cooling fan resistor when bad in the fall. A few weeks ago, it was again over heating because I had a leaky coolant reservoir cap. Now that I’ve replaced cap I notice that drives of 30mins or...

I need the stock black Air Vent louvers? My wife broke the Air Vent. she pushed it in that the connecting plastic piece. Does anyone have an extra one of this that they can sell me or at lest tell me a part number?

My car over heated last week, I pulled over and found that my radiator cooling fan was not running. After a few minutes, I turned the car back on and then the cooling fan turned on when the temp hit mid temp. I got home and switched relays for the horn and the high temp fan. Today, it over...

I am selling my used 05-09 BBK Cold Air intake for $150 Shipped or obo. BBK CAI are metal and are one of the few intakes that does not need to a tune to run. However, a tune is need to take full advantage of the intake. The filter has been cleaned since removal. All parts are included plus...

I got Mustang GT Dynotech Aluminum 3.5" from a sponsor of the boards. as I am trying to install the drive shaft, it is 3-4 inchs short. Now the rube joint appears to be very compressed. do I have to put it out? Help thanks

I am not sure this is the right forum for this but I have smoked turn signal as I put in 194 Chrome amber bulbs, I've put two set of this bulbs in from two different place and they keep burning out and the last set lasted a day. I was wondering if there is anything I should check?

The little sheath around the light bulbs has fallen off both of my fog lights. has anyone else experienced this? Is there any way of getting it out of the lamp? or am i going to have to buy two fog lamps?

I want to install my axles on my own but I never done it. From reading my haynes manual it doesn't look like a hard job. Would my 4.10 gears affect anything in the installation? Is there anything I should be careful of?

I have this very annoying rattle in my car. At first I thought it was the little shift boot holder thing that that goes around the shifter. However, when I hold it is was still rattling sometimes but it does help sometimes. So I grab the shifter and it goes away. Most of the time it rattles...

I am install my rotorpros rear rotors and pads and I can't get the piston to screw in enough. I have the ford caliper tool and I am turning it put it not going in far enough. any suggestions?

I am looking to buy adj upper control arm. I going to go with J&M Adj uca but then I found Spohn Adj uca for a lot cheap. I haven’t heard of Spohn and I am always worried about quality of an something that are that much cheaper then the rest, so I wanted to know what you guys think of them?

I need some help figuring out want tires I want to get just for the track. I love my BFGoodrich g-Force T/A KDW 2 285-40R18 for the street, but I only am running 13.35 with them. For next year, I want a set of rims and tires just for the track. What type of tire should I get? What size tire...

Ran mid 13ths most of the day, my best time was 13.35 @104 1.99 60' Mods I have are in my sign and I have 285/40r18 KDW2 tires Is this a good time with the mods I have? do I need the DRIVER MOD? Would DR help?

WTB: Driver Side Axle I bent the flange on my drive side axle when I slid into a curb last winter. I just want get a driver side axle that is oem style with studs?