Search results for query: *

Gents, Has anyone tried this stuff? HydroSilex.. An ad popped up on Facebook about it and I checked out their web site. it looks to me like a detailing spray, by the way it goes on/off, but they claim it to be a ceramic coating. Makes me a bit leery. what do you all think?

Hi everyone. I have been on the forum since around 08 or 09 and have learned from much more knowledgeable people than myself. You all helped me with the Whipple install, which was amazing fun for a winter project. Life has changed significantly for me (lost my wife to cancer) and it's...

Guys, I am going to purchase a new TPS sensor to attempt troubleshooting a sporadic engine failsafe condition. I read that the "new" TPS is taller than the original and may cause clearance issues. I checked the whipple and the tps plug clears the SC housing by about a 1/8". Anyone make the...

ok guys... 2005 with 10k miles...don't laugh... I have not driven the car more than 300 miles over the last year and it has basically not been driven for a year. I took it out 3 times this year and 2 of the times I goes into failsafe mode after about 5 minutes of running. not throwing any...

Folks, I have asked before, but it goes back a long way... i am now in Union County in North Carolina and will need to register my 2005 3v in NC... However, coming from NJ with a collector car registration, I have not had emissions tests. I have NO cats and rear O2 sensors are NOT turned on...

Folks, Cleaning out some parts I don't need and can possibly pass along to someone who does. Please PM me if interested in anything All parts are for 2005 3V or equal. All prices include shipping unless noted. Whipple 3.25" 6 rib pulley: $75 SOLD [/URL] Whipple 3v Intake Pipe: $65 SOLD...

Winter wheels and tires SOLD Guys my DD is an Infiniti Convertible and I used winter wheel/tire combo from Thanksgiving to early March. The car goes back now that the lease is over and I am offering up this combo to both Infiniti and Mustang guys since the bolt pattern and offset is the same...

I am most likely moving to NC from NJ in about a year and I was curious if NC has "collector car" registration like we do here in NJ. It limits the number of miles you can drive but more importantly opts you out of any emissions... therefore no cats... I only put on 1000 miles or so per year...

Guys, Installed the Stoptech 14" 4 piston kit onto my car and the banjo bolt specs have me concerned. It says to "Torque the banjo bolt to approximately 14 lb-ft, using a 12mm wrench or socket. Do not use a torque wrench, as overtightening the bolt can strip the aluminum threads, causing...

My Brother in law was trying to buy a new F150 out of TX and transport it to NJ. They refused to sell him the truck stating the F150 from TX would not pass emissions in NJ... This is the first time I have ever heard of new emissions standards outside of CA. Anyone have any insight??? Or is...

Putting up my Cadence Xa400 Amp and Kicker 10" sub for sale. The amp is unique since it can be mounted vertically. I had a piece of plywood under the trunk mat that the sub was mounted to. worked well. The Sub is a 10" kicker and It is a dual voice coil, 2ohm. I think its currently wired to...

Let me know if you have any.

Folks, Posting for a Bro In Law who recently had his clutch changed out at Evolution. When they took out the DSS drive shaft (newer model with CV joints) there was grease all over the bolts like something burst. Anyone have such an issue? the DS has been in for only a year and maybe 1000...

Hey guys. My car is due for new tires, but not because of miles. The car is an 05 and it has 8K miles on the tires and they were manuf in Feb 2005. Mostly just cruising miles and they have lots o tread. The only tire spinning has occured in 2nd gear going about 40-50mph:highfive: Im going to get...

Hey guys... trying to finish up the Kooks header install on brother-in-laws S197 and we ran into a spot that may take lots of trial and error, but i figured I would ask the experts. I dont like that Kooks didnt put any hanger system in for the H-Pipe, but that's besides the point. We have the...

Seems like bad news... I lent out my trq wrench and now that it's returned I was going to change out the belt for a new one. Well... while i was at it I figured it would check to trq of the water pump pulley bolts and a few others. The h20 pump seemed rather loose and wasnt htting the 20lbs of...

I have been looking for an aluminum Intercooler tank for my whipple setup to match the Moroso PS and Radiator tanks but could not find one. The only one avaialble was custom from Lethal and it's like $300... no thanks. I ended up finding out Canton makes an Aluminum tank for the 03 cobra...

OK, Im in the process of installing the Mac LT headers and they are hitting the heat shield of the control arm bushings. My mounts are 1/2 lower which may be causing the issue. I raised it up 1/4 inch and its better but still rubbing. Are these shields necessary? or should I just dent them...

Has anyone tried this combination? I have searched but I can only find threads of "I love what-ever-I-bought". It seems the prochamber is one of the best O/r pipes and kooks the best headers (SS and fit, good rep, and good results)... just testing to see if this combo has been tried. I would...