Search results for query: *

Thanks guys. Yes to the muffler hanger bolt holes. Tanner - what do you mean thread with insert? Like a helicoil is stronger than original bolt hole? I've never used helicoil before, but I assume it still allows one to remove the bolt if necessary ML

Long story short, after 14 years of countless muffler swaps, and obviously over-tightening of bolts, several of my muffler bolt holes are stripped. What's the best course of action to fix the holes so they're usable again?

All you need is the monitors set to "not supported" instead of simply turned off. This is exactly how my emissions tune works and I pass without needing to complete any drive cycle.

Rock auto has the cables and I think they'll be direct replacements!

These are close: http://www.mrbodykit.com/index.php?main_page=product_info&cPath=9_39_44&products_id=2756 http://www.mrbodykit.com/index.php?main_page=product_info&cPath=9_39_44&products_id=2762

Would this be silly to use with 4.30 gears?

I run Microseude FX1 Pro's with a 32" waist and they have been one of my favorite mods so far. Yes they are snug, but that's why you buy a seat like the FX1 - to be held in tight. The fixed backs don't bother me one bit, but I'm never driving for more than a couple hours at a time. They are a...

I'm still on the fence about how I would do mine since my car is yellow with black stripes. I think both pieces black would look fine, but if I painted the chin yellow/black striped then the splitter upgrade in black would pop even more.

Also, how much did it cost for you guys to have just the CDC classic painted?

I would like to see pictures of it as it comes unpainted (black)...

Very nice!

Hi Guys, I'm looking for pictures of the CDC classic chins with the splitter upgrade, but I only find pictures of the CDC classic when I try searching. Does anyone have any good pictures of these 2 exterior pieces on their cars? Here's the link to the pieces I'm referring to...

I, on the other hand, only use 1 set on each side and have passed. I honestly think that the whole 'non-fouler' thing is only a small (if that) part of the equation while the tune equates for 99.99% of the success rate...

Will this method allow for me to still remove the bolts? Or is the self-tapping method a permanent thing?

That's a good idea, but a little too late for me...

Several of the bolts that you use to fasten the muffler hangers to the body of the car no longer tighten. I know that it's the actually body of the car that is stripped and not the bolts themselves. I sued to switch exhausts quite often and also switch out the mufflers for emissions every now...

HMMMM, I'm not sure exactly what it is either. However, I'm positive that every sensor that was under/riveted onto the seat was transferred over to my Corbeau. I remember taking that sensor off the stock passenger seat, reconnecting it, and throwing it under my Corbeau passenger seat and haven't...

I put some Corbeaus in my 2005 last year and I think you're referring to the passenger's airbag bladder? When I installed my seats, all I did was disconnect the harnesses from the stock seats and reconnect everything under the Corbeaus. All appears to be fine EXCEPT I would not recommend...

NO.

I run LT's, O/R X, SLPs, and Hot Rods. I think it's sex and get compliments every time I drive.

I'm looking for a driver's side replacement door bezel and cannot find them anywhere. I see that your website only lists them up to 2004, are you guys able to locate some?

I'd take the FX1's any day over the stock seats. I'm serious when I say these two things the aftermarket seats will do for you: 1. Improve the overall feeling of driving 2. Improve the overall looks of your car I've had other drivers ask about my seats at stoplights, comment on the yellow...

I honestly love my FX1's, especially the microseude covering. I think the seats are comfortable enough and any uncomfortable aspect of them is greatly outweighed by their weight reduction, support, and looks. My car isn't a daily and it might get a tad annoying having to maneuver my way in and...

I have the FX1's and I love them. However, my fiancee haaates riding in my car now because the seats are too hard. Basically a win-win for me...

True, but I think these look cool because they get rid of the outer plastic 'barrier' giving the headlight area a sleeker look.