Search results for query: *

I have always run VR-1 10w30 (dino oil) in my built 3v's break-in and then after. Finally got 500 miles on my new motor and wanting to run Driven (joe gibs). Radical build. -10.5:1 custom diamond pistons teflon coated with ceramic tops -30psi boost -Custom L&M cams -VCT locked out...

My car is an auto with a 4r70w swap currently setup with manual valve body. I am pretty sure I can use a auto or manual pcm but will verify with Lito

Would really prefer auto. would like the whole harness including bec plugs and pcm plugs etc.

Still dicking with this no spark issue on my wire tuck. PCM will not ground the coils. I will figure it out but part of the problem is the online wire diagram which sucks to say it politely. Anyway, now may be the time to drop OEM PCM and move on to BS3 stand alone computer. I will...

For testing. Would be easiest if it were 07-09 auto. Need all the bec and pcm stuff. Tracking down freggin spark issue after my wire tuck. fml

Yes I have the stupid connector catalog for the complete WPT (wire pigtail). I don't like taking it in the ass tho for a couple small pieces of crimped wire to go in those dumb things and a couple pieces of splice. Who wants to splice in anyway when the connectors are so easy to get off and...

I just finished a wire tuck and have no spark. Datalog shows rpm and replaced CKP just in case. So, signal to pcm from reluctor "should" be good. The wire to CKP was not extended, it was cut only to pull it where it needed to go and the shield was replaced including splicing the drain...

Anyone got one handy they could post? Specifically of those connectors which are the bottom two connectors on the PCM. Thanks..

Anyone know the labels of the bec connectors? Need to track down c174 and c194. Want to check continuity. Not getting spark. Just did wire tuck and everything works... except no Damn spark. Only checked cylinder #1 as had to get ready for work

sold Yes, this is the horribly expensive one with dual bearings. Blowers are hard on them so this was designed around supercharged applications but can be used on most setups. Have had this one for a while but is low miles. I was chasing a bearing noise so sent this pump to meziere...

How many of us have been here done that? I originally was in the mindset that the steel tensioner was the big problem. It still may be a factor but in the end if I was using the newer shitty plastic tensioner that do not ratchet like the steel ones I would have lost the motor when pressure...

Going to have it polished next week then start installation... super stoked right now. Just a few odds and ends but this thing is wicked. Will do a write up in tech when done

Evidently between a couple machine shops a few of my arp studs are out of spec Looking for best deal on new set 2005-2010 3v Thanks

Installing a Department of Boost blower kit on a friends car and not using some of the items from his previous setup. Selling parts for him. All prices INCLUDE shipping to CONUS and include paypal fees unless otherwise posted Came off 07 Shelby GT with just over 20,000 miles. Few blemishes...

SOLD! Installing a Department of Boost blower kit on a friends car and not using some of the items from his previous setup. Selling parts for him. All prices INCLUDE shipping to CONUS and include paypal fees unless otherwise posted This is not the chepo strut bar you see on many sites...

SOLD! Installing a Department of Boost blower kit on a friends car and not using some of the items from his previous setup. Selling parts for him. All prices INCLUDE shipping to CONUS and include paypal fees unless otherwise posted Next up are Steeda Underdrive pulleys. Not sure how many...

Installing a Department of Boost blower kit on a friends car and not using some of the items from his previous setup. Selling parts for him. All prices INCLUDE shipping to CONUS and include paypal fees unless otherwise posted You will only need the odd-shaped gasket on the passenger side...

SOLD! Installing a Department of Boost blower kit on a friends car and not using some of the items from his previous setup. Selling parts for him. All prices INCLUDE shipping to CONUS and include paypal fees unless otherwise posted First up is a set of BBK fuel rails for 05-10 3v. May fit...

Need a tr3650 26 spline input shaft and a 26 spline spec stage 3 disk or stage 3+ for a local buddy of mine. He is a newb on the forum Devcon_7 be gentle, I have spent most his money already :beer:

Well shit. Just FYI... I installed the BMR sway bar relocation brackets a LONG time ago but finally got around to installing the BMR LCA relocation brackets. On the BMR site nothing is mentioned under the info section or installation for the LCA relocation brackets interfering with the BMR...

I am regretfully going to run the ID1300 instead of the ID2000 as my car will sit long periods of time and dedicated e85 system. Will be ready to pick some up here in the next two weeks or so. Still waiting on some wanker to send me a manifold lol Send me a PM on what you can get them for in...

I should probably search but are the head bolt lengths different on the 2v 3v and 4v? Just curious about torque plate spacers etc..

Man I fucking HATE calling those people. EVERY single time I call there is a runaround, or some JACKASS trying to tell me some shit. Today I called to ask a VERY simple question product availability and wait time. No surprise,, I was immediately told I was wrong yadda yadda about what I...

Sold or will be keeping it Installed new trans with tranny brake so no longer need this. http://www.americanmuscle.com/msd-launch-master-2step-9910gt.html Priced for quick sale $100 shipped 48 USA Paypal fees included If I do not respond to your inquires in a timely manner it is likely...

Looking to complete a DOB kit for a local friend. All we need is a manifold but he is on College budget and every dollar counts. His Daily Driver was totaled by an illegal (Illegal was at fault and had no insurance). That whole deal him in a temporary jamb or he would have bought a new one...