Search results for query: *

My reman'd Motorcraft alternator in my 2005 GT is starting to whine. In doing some research here, it seems like the recommendation is to use the 2010 GT alternator as it's more reliable. I am looking at a reman'd Alternator on RockAuto and a quick question that I wanted to confirm. Is the...

I have an oil leak and the likely culprit seems to be the driver side valve cover gasket as I see oil on the power steering pump below it. The oil is then making it's way down the power steering hose and leaking on the ground. Anyone ever run into an issue with leaking valve cover gaskets...

I am looking for 14" Brembo 4 piston brakes. I'd be open to buying calipers, pads, and rotors or just calipers and sourcing my own rotors/pads. Thanks! Jason

I have an Autometer Cobalt Wideband gauge. I’ve got it temporary wired and sync’d with LiveLink, so it’s working fine. I was wondering if most people permanently soldered the connections together and just hid the datalog cable under the dash or used a quick connect method using male and...

I am looking for an MGW shifter for a 05-10 5 speed. Anyone got one?

Looking for a set of Charge Motion Delete Plates (CMDP's) for an 05+ 3v. PM me if you have some available.

Looking for the trunk lamp assembly for an 05-09. The clip on mine broke and it's rattling, so I would like to replace.

I am looking for CMCV delete plates for my 2005 Mustang GT. Anyone have any laying around?

I had new FRPP "carbon" clutch packs installed when I had my 4.10 gears put in. I've got about 750 miles on them and I've been noticing a groaning noise when taking tight right turns. As when turning to the right at speed, there is a slight jutter than I can fell. The shop put in Royal Purple...

I've got some wax and compound on the black plastic trim peices. What's the best product to remove it? I've heard of using peanut butter. Just curious what's the best product. Thanks!

Anyone ever have an issue with their Tokico D-Spec adjusters getting stuck? My front ones won't move. I actually bent the Tokico supplied adjuser the first time I tried to adjust them. I've tried soaking the adjustment hole with WD-40 and PB-Blaster and can't get the fronts to move.

Anyone have a black 05-09 door sill with the stainless IUP insert laying around? Mine started to pit and looks like crap. I'd like one that's in very good condition.

Some background; I am running a Vortech HO kit that make 10 lbs of boost. Last fall I was getting a P01296 rich code which I thought was a tuning or vacuum leak issue. The car didn’t feel as strong up top and I was going to take it to the dyno to see what it was currently putting down to the...

I am looking for a FRPP M-4210-B install kit and M-4700-C Carbon Clutch Kit. Before I purchase new, I figured I'd see if anyone has either laying around. Let me know, Jason.

Anyone got one for sale?

I cleaned my garage and have the following parts for sale: 1. CHE adjustable upper control arm with delrin/poly bushings. This was on my car for about a year and is in very good condition besides some surface rust where the control arm bolts to the rear end. You can use this to adjust your...

I went to the track yesterday and ran a new PB, but was a bit disappointed. I thought the car would run .2 better with a 2-3 more mph thru the traps. DA was 1158 My setup is as follows; 2005 Mustang GT 5 speed manual Vortech Supercharger HO intercooled J&M UCA, J&M LCA, Tokico D-specs, FRPP...

I am wondering how you are adjusting your D-Specs front vs. rear at the track. I did a search and found one thread where I found two options: 1. F-6.5 / R-4 2. F-7 / LR-5 RR-3 I have a 2005 GT manual with a Vortech blower making 475rwhp. The car has the factory 3.55 gear in it. I...

I am looking for 17" drag radials. Anyone got some for sale?

I've seen them for sale every once in a while on here. Anyone looking to seel their set or know of anyone selling? Jason

What’s the consensus on the FRPP intake manifold with boost? I have a Vortech on my 05 and was looking for a little more power without putting a smaller pulley on. My car made 474/412 to the tire a few years ago. I still have the factory charge motions and was thinking about removing those...

I have 85K on my 05 and I am thinking about going through the rear and rebuilding it. I was also thinking about upgrading from the factory 3.55. Here is my plan: 1. FRPP 4.10 "A" gear 2. FRPP Carbon Clutch Kit M-4700-C 3. M-4210-B Install Kit 4. M-1225-B1 Wheel Bearing and Seal Kit 5...

Hi, I am getting a misfire code P0354. This is cylinder 4 which is the closest to the firewall on the passenger side. I went to my father in laws store and grabbed a brand new NAPA Echlin coil plug. I plugged it in and reset the code. I drove the car and it's still stuttering a bit and threw...

My IUP Steering wheel is getting worn and I am looking to replace it for a GT500 or Bullitt steering wheel.

As I was driving home last night, the "check charging system" message popped up in the cluster. I recently installed a new alternator and the battery is less than 1 year old. My radar detector is showing the voltage between 11.7-12.1. It used to be mid 14's, prior to last night. I checked...