Search results for query: *

Looking at swapping to e85 on my 2012 I found a great deal on a 20amp kennebell bap would this work fine? Or does it have to be 40amp? Stock fuel setup nitrous car right now, getting lu47s and bap ASAP!

Hi everybody I have a 2012 gt auto, bolt ons, and nitrous Stock gears Stock front struts No front sway bar Strange single adjustables in the back (set full stiff) Bmr poly tubular rear lowers Steeda adjustable upper with they're mount set in stock hole Bmr lower relocation brackets set in...

Looking for a pair of new or used 05-10 GT front brake caliper brackets. 05-10 GT only! Price shipped to Palmdale, ca 93552 Thanks!

Took the car out to the strip today, and after making a few passes and swapping the rear tires I noticed a line on the outer side of both tires from them rubbing. Anybody else have this issue? Car is a 2012, 275/60/15 m/t et pros with sve 15x10s and 2013 cobra jet springs I don't think...

So I feel like my car should be 60' a bit better, and need to figure out what direction to start adjusting in. Car is a 2012 auto nitrous Best 60' is 1.65, avg 1.7 with a little bit of slip Suspension is, bmr lowers w/ bmr relocation brackets in top hole of brackets, 15x10 rears with 275/60/15...

Well my dads stepping up from nitrous to a blower setup on his 2012 boss Car has cat deletes, intake, bama tune and a 100 shot now, found a killer deal on a New vortech JT trim tuner kit with vortech BAP and 8 rib upgrade! Going to pick it up tomorrow. Now i know we need the adapter kit for the...

I bought a used circle d converter off of a well know guy here on s197, Had it installed at the local tranny shop, and noticed it has a rattle (almost sounds like a heat shield rattling) at idle in park/neutral. When creeping (car in gear foot off brake) it makes it at a certain rpm too...

Trying to figure out what stall speed to go with on a 2012 5.0, bolt ons/ and nitrous. Going to try and order one in the next few weeks...

Has anybody disconnect just one sides links on the front sway bar, vs removing the whole bar? Does it work fine? Looks like it should, jut wanted to see if anybody else has tried it...

Looking for used or good prices on new 15x8 or 15x10 rims (2) weld rt-s (black centers) (best price new- 560 shipped) racestar direct drill or sve Prefer the sve because they dont require special lugs! Located in so cal. Thanks

Anybody know the part numbers for weld 15x10.25 rts black spokes for a 2012 gt? My buddy can get me a good deal on them but I need the correct part number... Thanks!

I screwed up my tuner when it was updating firm ware, and i need to manually put a old firmware file on the device so i can then re update it. anybody happen to have the file floating around their computer?

I have a 2012 gt, which I deleted the cats in, got the proper tune from bama, and it has been running great. Yesterday I removed a rear 02 sensor, an replaced it with my wideband, however now I get a check engine light for the 02 not heating up. I had this same setup on my 06, and it never...

Looking for a fuel line/nitrous adapter for a 2011+ 5.0 Bmr upper control arm (adjustable) 2011+ (hammertone preferred) And a roush vent gauge pod 2011+

I have a long block out of a 2006 mustang It had a problem with a bad cam follower which has been fixed Has roughly 60k miles on it I can have it assembled in less than a day, or i can leave it open so buyer can inspect it. everything is in excellent shape *new* 2013 gt500 oil pump (billet...

Traded my 4.6 in for a 5.0 all parts must go! 4" coast driveline aluminum one piece driveshaft worked great no vibrations comes complete sold bmr drive shaft safety loop sold pacesetter long tube headers and matching mid pipe with new 02 sensors $350 *local pickup only* bbk under drive...

There is a local craigslist add with some parnelli jones 3v cams. Seller has no idea the specs on them. Does anybody know anything about them?

Looking for the best price on a complete t56 magnum xl swap for a 2012 boss The mt82 took a crap, time to upgrade!

I recentlly replaced my stock door subs with some kicker comp 8" 4ohm subs. However they do not seem to be working. im wondering if maybe i wired it wrong? i followed the shelby sub upgrade install instructions, and used two wires (white and grey + white and black -) but no dice. Any...

So traction seems to be the issue on my 06 auto with bolt ons and a bit of nitrous. Currently my suspension is stock besides upper and lower rear control arms and a set of 275/45 r17 m/t et streets. I'm looking at getting strange adjustables for the front and back And I'm undecided on...

My car normal runs between 14.1-15.0 a/f under part throttle and idle All of the sudden it'll start up and slowly climb from 14.5 to 10.0 in about a minute. What could cause this? A/f under wot seems normal Fuel pressure is normal. Fuel system is stock besides a aem 320lph pump which I...

So i went and did a little data logging on my car to get ready for a tnt next weekend, and on the way home the car randomly started missing/ running rough wideband shot up to about 16.xx and as soon as i could get out of traffic, it started running just fine, wideband went back to normal (low...

I have a bolt on- nitrous 3 valve with ht0 plugs Looking to gap the plugs for a 150 shot of nitrous what do you recommend?

Have a bit of a clunk in my rearend. .011-.012" backlash on ring gear, however the spider gears in the posi are .020"+. How do you shim these? Are they shimmed on the clutch pack gears, or on the lock pin gears?

Im looking for a better tune for my bolt on - nitrous 06 gt. I have a sct x3 with bama tunes, but i feel its lacking. So who would you recommend for a solid email tune for a nitrous 3 valve?