Search results for query: *

Does anyone have any experience with these on the MT82?

I need to replace one of the heater hoses that runs to the firewall into the heater core. It's tight back there and before I spend 20 minutes wrestling with it, is there a tool to remove it or is it a squeeze and pull setup? Thanks

These mufflers will fit the 11-14, GT and the 11-12 GT500. They have 4k miles on them and have a nice deep tone. 190 shipped.

I have a 2012 Manual that I have been chasing a vibration on. It seems to really come on at 80mph. I was running an aluminum shaft and swapped back in the stock shaft but the vibration was still there. Set the pinion angle to a -1. Got a bit better but not a whole lot. On a whim I had the stock...

Take off GT500 blower that looks as if it has never even been run. Includes elbow and TB with electronics. Also it includes the boost bypass valve and the vacuum lines for it. $600 shipped, shipping will be at least 70 for this. This will be a perfect blower for the upcoming DOB 5.0 kit. Buy...

On a simple Google search I have not found anything on replacement rotor packs for the 2.3 TVS. Is it just pure luck to find a set for sale?

Looking to see what's available before I pay full retail. Looking for a street version adjustable UCA and the bracket for an 11-14.

So my tug boat is in shipyard in Tampa and when home my trip to the drag strip resulted in shitty 60' so I need a set of Relocation Brackets. I searched around and spoke with Kelly at BMR and realized the shop is only 20 min away. He promised a deep discount if I came over. The outside of...

looking for brackets that will fit a 2012, bolt in if I can.

Here is a complete 8.8 out of a 2012. Only has 5k miles on it. Worked fine swapped in a 3.73 rear. Will sell the bare housing for 300 plus shipping or complete for 500 shipped. Located in 18509 North east Pa

Everything SOLD This is a complete rear from a 2012 Gt500. It has 17k miles on it and a tweaked axle tube so the whole thing isn't for sale unless someone wants to replace an axle tube. 3.55 gears 75 shipped GT500 diff, has the carbon disks 100 shipped Gt500 cover 50 shipped Located in...

So I have a 2012 that was previously a salvage which is up and running and clear of the enhanced inspection. A few months ago when it wasn't quite finished I went to the local gas station and filled it up. Then going to leave it wouldn't start but turned over. It went through 4 start cycles be...

Looking for the MT82 stock clutch and pressure plate with low miles. shipped to 18509. Thanks

I need a laptop to data log to and the Chrome books on Amazon get great reviews but I saw one review that says it doesn't download traditional programs. I'm computer challenged and need to know of it will work. SCT tuner???

Does anyone have a set of the billet watts link arms laying around?

I have a 2012 that was in a wreck and harnesses were replaced and all else seems to be up and running but a few things are not. Passenger window won't work but the door lock button does. Passenger electric seat will not work. Stop lights and rear directional won't work, rear hazards as well...

In a video clip of a Roush TVS on a 5.0 the blower whine was pretty faint. I had a Magnuson and it was whisper quiet. I have a project coming up this summer and will be using a TVS blower. Do the FRPP whipple kits still have that great audible whine to them or are all of the TVS blowers quiet...

http://youtu.be/bEl3S61t9p4 I bought a wrecked 2012 a while ago and while putting it back together the manifold was trashed so I decided to do a little modding. This manifold is from a Taurus and uses spacers with the injectors built into the manifold legs. Ive replaced a bunch of harnesses and...

I am looking for a newer panhard bar. Read one with good and not dry rotted rubber bushings. I am modifying a Saleen Watts link and the link arms use the same rubber bushings. I am gonna try and press out the old bushings and replace them but it they dont come out willingly I will just shorten a...

I have a 2012 that I am trying to figure out where this plug goes to. Its located in the drivers lower front facia area. It is attached to a pigtail that branches off just before the horn assembly plug. The pigtail is about 12" long. Im rebuilding a wreck and some things were missing before I...

I have a 2012 I am waking up from a wreck. All bags deployed and the car is almost complete waiting on a side impact sensor and a clock spring. As I powered up the car of course everything in the dash is freaking out. I have a tuner on the way and will try to clear as many codes as I can. I...

Ok I am just about at the end of my build and funds are on fumes. I have a 2012 3.7 with the 2.73 gears and want to swap them out to a 3.55. I have an entire rear end out of a 2012 Gt500 with the 3.55 gears in it. Axle tube is tweaked so i cant swap out the entire rear. Having the better carbon...

I need for a 2012 Hood latch striker Passenger side airbag, I have a cover Transmission crossmember center piece Sent from my SAMSUNG-SGH-I337 using Tapatalk

I have a Gt500 differential cover for 50 shipped. A Gt500 sway with 20k miles on it. Slight scrapes from dragging on ground when it was moved. 60 shipped. Gt500 Lower control arms 30 shipped. Two p 235 50 18 Pzero Nero 2300 mikes 9/32 tread. No funny wear. No plugs 120 for the pair or 70 each...

I have a 2012 I bought as a wreck and I have replaced all the airbags but have not gotten to the steering wheel airbag yet. Does the clock spring have to be replaced, drivers air bag fired but does that kill the clock spring? I am sending out the airbag module under the armrest to be reset. Do I...