Search results for query: *

Excellent condition. $350 plus shipping.

NGK 7554 plugs removed out of my mustang. Gapped are .032. 5k miles on the plugs. $35 shipped

I have a 3 valve with a whipple ho, hot rod cams and long tubes. It was dyno tunes by Lund with straight through borla type s mufflers. I recently put the stock mufflers on due to the recent birth of my daughter. Does the car have to be retuned when changing to a chambered style muffler? Thanks...

Does anyone know the Motorcraft part number for the TPS? IM getting both DY 1116 and DY 1164.

Does anyone know the Motorcraft part number for the L and R Downstream Oxygen Sensors?

I have used 02 foulers in the past to get me through emissions test in ny but tonight I threw a p0159 code. Has anyone ever gotten this code when using the foulers? I am thinking about drilling them out to get some more air flow to the 02 sensor. At this point I'm just hoping that I don't have...

Hopefully someone can help me figure out what is causing this: Under 0 vac I am randomly throwing a wrench light and the car is turning off. It does start up and run fine after. The car does also run lean when cold and will misfire until it warms up to operating temperature. Mods are...

I am looking for advice on which dual action polisher to purchase for home use. I purchased a black car for a daily driver and the paint needs some tlc. After previously owning a black car, I know that it will need a lot of upkeep so I figured I would just purchase the dual action polisher as...

Sold!!!!

Can you get the id1000 in ev14 length for a whipple? Would I have better drive ability with these as opposed to gt500 injectors? Anyone know of where I can get a good price?

Does anyone know the part numbers for the motorcraft rear main seal, slinger, and housing? Are the bolts one time use only or should I replace those as well. Parts are going on a JDM 302E

Looking for oem exhaust manifold studs. Let me know what you have or where I can get them

I can't find the torque specs for the spring loaded tensioner. Does anyone know them off hand?

I need ev14 60lb or 80lb injectors. Let me know what you have or where I can get them for a good price.

I am putting together a 302E and whipple 2.3 and have a question regarding injectors. Will the 47#er's be enough for 550-600 rwhp. I plan on going with 15psi (pump gas only)

What size flywheel bolts do we have (JDM 302E)? Do the ARP's come in sets of 8 or only 6? I am assuming I have to buy 12 and just junk the other 4. If anyone knows where I can buy them and save some money let me know.

I have a 302E with an 8 bolt and I want to purchase a Spec steel flywheel but am not sure which one to get. Its mating up to a 26 spline tr6060. Does anyone have a similar set up that can tell me the part number I need?

I am putting my 302E on an engine stand and need to know what size bolts I need for the block. I am using an engine stand from Jegs and just don't know what bolts I should or shouldnt get.

I am installing my 302E and just wanted to make sure I have all of the parts I need before I start. I purchased the steel bodied tensioners already. What else do I need? I am assuming the timing chain and guides should be changed as well. Am I missing anything else?

I am selling my Whipple 10 Rib Belt Drive System. It comes with everything needed for install including directions and belt. The lower pulley is set for 10-13 psi. The snout has a small scratch on it that can be placed down so it is not noticable. I can send detailed pictures to anyone who is...

I am looking for a new unused 10 spline clutch to handle around 800 ft/lb. If anyone has one they are looking to sell please let me know.

Getting ready to start the build and need to find steel timing chain tensioners and guides. If anyone has them or knows where I can find them cheap please let me know. The build is starting to get out of control money wise

I purchased the whipple 10 rib belt drive system designed for 10 - 13 psi and now I need more. I was hoping that someone would have a lower crank pulley they are willing to sell or trade. Thanks!

I haven't had time to install my shortblock so it has been sitting in my basement. What should I do for storage and how often?

Took the mustang to work today after not driving it for a month and it threw a wrench light and stalled in third gear while crusing with no throttle. I was able to turn the ignition off and restart the car but could not pull any codes. I am thinking it may have been a random misfire possibly due...