Official boss block build

[Dillon Dollar]

I have 3 walboro 400s

Sent from my SPH-L900 using Tapatalk

 

[GB10]

I would personally run 2000cc injectors. I don't like running higher base pressures with electric pump setups due to heat build up.

 

[Dillon Dollar]

That's probably what ill do

Sent from my SPH-L900 using Tapatalk

 

[JPO8GT]

I'm running the I'd 1300's on my turbo build supposed to be good on e-85 & e-98 too.

Sent from my XT1080 using Tapatalk

 

[Dillon Dollar]

To how much power?

Sent from my SPH-L900 using Tapatalk

 

[Dillon Dollar]

Static compression on my engine is 10.2:1

Sent from my SPH-L900 using Tapatalk

 

[JPO8GT]

I have a build thread going motor spec is 11:1 - 11.25:1 I'm waiting on the head cc info from RGR to know exact cr.
On good e-fuel it should clip near 1200 rwhp at full tilt running 3 Walboro 465's JPC mentioned that the ID 1300's are the injecter dynamic's e-85 corn fuel work horse.

Sent from my XT1080 using Tapatalk

 

[Dillon Dollar]

Hmm very nice. I have 3 400s I hope they'll do the job

Sent from my SPH-L900 using Tapatalk

 

[JPO8GT]

If you have seen that JPC Epic red boss build thread its a 1400 HP build running e- fuel their also using ID 1300's on his build.
When researching injectors I seen where some tuners strugled getting tune right with 2000's not sure how valid those sources we're.

Sent from my XT1080 using Tapatalk

 

[JPO8GT]

Hmm very nice. I have 3 400s I hope they'll do the job

Sent from my SPH-L900 using Tapatalk

I think you'll be fine there making crazy proven power with the ID 1300's 400's are not small pumps by no means.

Sent from my XT1080 using Tapatalk

 

[Dillon Dollar]

I think ill go with the 1300s or 1600s.

Sent from my SPH-L900 using Tapatalk

 

[BruceH]

Hmm very nice. I have 3 400s I hope they'll do the job

Sent from my SPH-L900 using Tapatalk

IIRC the 405 walbro pumps don't like e85. You might want to research it a little.

 

[Dillon Dollar]

Im suppose to have the e85 versions

Sent from my SPH-L900 using Tapatalk

 

[Dillon Dollar]

Im under the impression a 405 is different than a 400

Sent from my SPH-L900 using Tapatalk

 

[Dillon Dollar]

Does anyone know what I should use for a crank balancer

Sent from my SPH-L900 using Tapatalk

 

[ethic1]

Innovators west are nice and what I went with. ATI makes nice ones as well.

 

[Dillon Dollar]

Alright ill look into it

Sent from my SPH-L900 using Tapatalk

 

[JPO8GT]

I choose innovators west I had great service from one on my 3 valve and I am now going with iw on my coyote the quality is eqaul to ati but little less expensive.

Sent from my XT1080 using Tapatalk

 

[Dillon Dollar]

I had an iw on my old blower setup ill probably go with that

Sent from my SPH-L900 using Tapatalk

 

[Dillon Dollar]

Anyone know what I need to use to get the th400 transmission to work with my speedo. And also does anyone know what I need as far as a cross member for wheb I mount the transmission.

Sent from my SPH-L900 using Tapatalk