Starting to work on my mancave engine block table and end table and need a few pieces...
Main items I definitely need:
4.6 head bolts - Purchased
4.6 flywheel - Purchased
4.6 flywheel bolts (flywheel to crank and balancer/pulley bolt)
4.6 Rod Ends - Purchased
4.6 main caps
Bonus – Would be cool to have:
4.6 heads
4.6 intake manifold
4.6 valve covers
4.6 front cover
4.6 water pump
Head bolts - if you are changing/removing your heads and will be tossing your head bolts... I want them. Need at least 8 but would love a full set.
Flywheel - don't care if it is usable or not. Just needs to be flat. Using it as part of an end table. Can paint if it has issues.
Flywheel bolts - not as necessary as I can get some generic bolts from the hardware store... just trying to keep it authentic.
4.6 Rod Ends - Need 4 end caps for the Rods where they bolt to the crank. Need bolts too if you have them.
4.6 Main Caps - Need at least two... not sure if I am going to put the crank in the block or not but want the option.
Heads - as long as the outside looks good I don't care about the block side or the valve cover side... prefer aluminum and stripped but let me know, I can always paint them to look like aluminum and find uses for some valves and springs. Don't care what they are out of and don't care how many valves... just want to mock up heads on a block.
Intake Manifold– as long as I can clean it up and paint it… don’t care if it is usable or not.
Valve Covers - don't care what condition they are as long as they can be cleaned up and painted.
Front Cover - see valve covers.
Water Pump - exterior portion needs to be able to be cleaned and painted, don't care about what can't be seen when bolted up.
Let me know what you have and what you want for it to ship it to 68028
Main items I definitely need:
4.6 head bolts - Purchased
4.6 flywheel - Purchased
4.6 flywheel bolts (flywheel to crank and balancer/pulley bolt)
4.6 Rod Ends - Purchased
4.6 main caps
Bonus – Would be cool to have:
4.6 heads
4.6 intake manifold
4.6 valve covers
4.6 front cover
4.6 water pump
Head bolts - if you are changing/removing your heads and will be tossing your head bolts... I want them. Need at least 8 but would love a full set.
Flywheel - don't care if it is usable or not. Just needs to be flat. Using it as part of an end table. Can paint if it has issues.
Flywheel bolts - not as necessary as I can get some generic bolts from the hardware store... just trying to keep it authentic.
4.6 Rod Ends - Need 4 end caps for the Rods where they bolt to the crank. Need bolts too if you have them.
4.6 Main Caps - Need at least two... not sure if I am going to put the crank in the block or not but want the option.
Heads - as long as the outside looks good I don't care about the block side or the valve cover side... prefer aluminum and stripped but let me know, I can always paint them to look like aluminum and find uses for some valves and springs. Don't care what they are out of and don't care how many valves... just want to mock up heads on a block.
Intake Manifold– as long as I can clean it up and paint it… don’t care if it is usable or not.
Valve Covers - don't care what condition they are as long as they can be cleaned up and painted.
Front Cover - see valve covers.
Water Pump - exterior portion needs to be able to be cleaned and painted, don't care about what can't be seen when bolted up.
Let me know what you have and what you want for it to ship it to 68028
Last edited: