Search results for query: *

I sure like the Harris plate for neatness & I'm sure a harder hit. It will be my choice when I put nitrous on my 08 Bullitt. Pics when you install.

Real nice set-up. I can't wait for dyno numbers.

Mikey knows nitrous!! Nice video.

You just need to weigh the bottle when full then after runs weigh it to see how much is left. I agree I always run about 1150 psi with a adjustable bottle heater that turns on below 1150 psi. By the time you do a purge it will be a little lower. If you start out with a bottle at 900 it will be a...

They have 192* & mine read 196* actual using Dash-Hawk, using a 180* will drop you about 10* with fan temp change. It will allow a little more timing.

08 Bullitt soon to be fast!

08 Bullitt soon to be fast!

Stock 192* replace with 180* get the fans programmed for the new stat to come on quicker.

I got mine off e-bay (Innovate) $280.00 to my door. Price was right for sure.

About 2 hours at most after getting the bung welded in. I was real picky with mine even using black mesh wire wrap to keep it all neat under the hood. I used a fuse tap also for the power wire. Here is a pic of the Roush cup.

I have the Innovate XD-16 gauge in my 08 Bullitt driver side vent in the Roush vent cup. Fits perfect. Best gauge for correct A/F I have used one in the last 3 cars I have owned. Easy install. I had the bung welded on driver side (inboard) about 4" below factory header in the 2:00 O'clock position.

A lot of people have gotten rattles they think are the mufflers only to find out it is a exhaust rattle, usually after the exhaust gets hot it expands & the driver side hits by the bracket. It only gets close when the exhaust is real hot. It sounds like it is the muffler. You will see a area...

I will be getting them installed this summer by Gear Heads in Arlington Tx. Travis said he would do the Hot Rod Cams turn key for $1140.00. I don't have a garage so I will just have them installed for that price also get him to load a tune for me. They do installs on them all the time so I'm...

Put some more timing into the lower rpm range to smooth it out.

This is the plate to get from Harris Speed also they make custom length hoses covered in black carbon fiber look black with black fittings. I have my hoses ready (from Harris). I am building it a piece at a time till I get everything to do it right the first time. Like the above but with black...

I keep leaning toward the bottles in the back seat with a seat-delete. I also will go with the Nano system. Here is a guy called Bite-The Bullitt that post on Imboc with these pics of his set-up. I also like the twin bottles with Harris Speed behind TB plate. I will have the plate nittrous/gas...

DashHawk also does 60ft times & 1/4 mile times with-in about 1/10th accurate. It can also be used for a shift light or warning on temps ect. It does lots of stuff plus clear/read codes see if you are getting timing pulled for spark-knock plus more. Just plug in the computer port. Cat temps &...

Buy a Dash Hawk & get all the gauges plus more. I have one & keep it on spark advance, fuel pressure, engine temp & rpm. The temp cam move as much as 20* & the factory gauge doesn't even move. Factory gauges are way off.

You need to spend the money on a good wide-band A/F guage & do a easy A/F tweak. You can just do a tweak yourself & keep it tuned in both Summer /Winter. With a good base tune it's not rocket science to make small adjustment yourself to get a perfect A/F & $400 is crazy to spend. Just my take on...

Vary clean & nice. Like the battery area & look. Good job!!

Yes you can if you don't have cats.

Looks like the Ford Hot Rod cams like the nitrous. My choice also when I do a cam change (great sound). Perfect combo you are running for sure.

Good set-up for sure (new) grab the deal.

Wow! Yes you do have a lot more left on the table. Nice set-up for sure. Where I want to be someday. I say you will be getting a boot for going below when you need a cage for sure (11.50) I say 11.40's easy enough with your mods & better tune with 125 shot. You need to see where your A/F is...