Search results for query: *

Hello all, I built a nice '91 Fox with a 5-lug conversion. I later sold it and the current owner bent one of the polished aluminum wheels on it where it can not be repaired. I've called Summit Racing and American Muscle along with a few local wheel and tire places here in Houston. The wheel...

After 80K miles on the OEM struts it was time for replacements. I bought some used Saleen N2s from a member here. The plan was to use them with a pair of Bullitt springs I've had for a couple years now. From what I've read, they lower the car 3/4" with the ride being slightly firmer than stock...

I bought a rear Saleen PJ rear window louver (the big black one) from eBay a year or so ago. They look like these. They didn't come with mounting brackets or hardware. I've spoken to a few Saleen friends and they say that the brackets are made from 2-1/2 x 3-1/2 sheet metal "plates"...

I would get the "cam positioning sensor" code, I'd replace it, and in a few months it would come on again. Also, the car was becoming more and more unpleasant to drive. I would put in the clutch, put it in gear, and pull out the clutch and the car would either buck forward or the rpms would drop...

I just bought it and I'm using it with a Wacom graphics tablet. The Pen & Touch one, I think. Anyway, here's the problem: I'm sketching and the lines are "off" because they're not as smooth and controlled as the ones I see on YouTube. I've made identical settings to the pencils/brushes and...

I bought a set of SSS mufflers from a local Stang club member. He thought they were the Off-Road ones but wasn't sure. There's also an Adrenaline and a Terminator. There is no discernible difference as I can see and there is no part number. Yes, I tried to contact the manufacturer. I...

I put off installing my pro chamber with the Mac mufflers I already had. I installed it this past weekend. I broke a stud in the process and paid the local stealership $36 for a stud and nut. Ouch! So, I cut the legs off my old OEM h-pipe to keep the catts, tie in the PC, and got her done. The...

Hello all, I finally trimmed the fat off my Shaker hood this weekend and while it looks great, it did expose all those ugly wire, coils, etc... I've looked online for coil covers but I can only find '11 and up GTs and the GT500s. Do they make them for '05-10? I'm not thrilled about spending...

I have a Shaker hood. After 6 years of ownership it was looking pretty weathered. So, I disassembed it and painted the shaker flat black. I reinstalled it and turned the car on. The idle dipped a little then stabalized. I watched it a few minutes then moved the car. Again the idle dipped. I...

For reasons I will reveal at a later time I've been riding around town with the driver's seat and dash. All other interior is out of the car. I noticed that the tranny tunnel was heating up the cabin (with the A/C on). I put my hand on the passenger side about where ones knee would be. It was...

Not sure if some OEMs or aftermarket ones will do the trick. I bought a Mac Prochamber from a member here this weekend. I cut the catted section of the stock H-pipe and now it looks like I'll need some clamps to button it all up. Let me know what you got. Thanks all, Gerardo

I have the Mac mufflers with a Bullitt H-pipe. It sounds nice at idle, real good revving thru the gears, and awesome at WOT! It has zero raspy trumpet syndrome and I love the burbling when I downshift it. There's the dreaded drone at 2K rpms but I've learned to shift and live around that until I...

Planning on buying the $1000 Brembo kit that a vendor is selling here. However, I'm told the "18 Bullitt OEM wheels will not clear the calipers. The offset will NOT allow the wheel to sit flush against the disc's face without the use of spacers. Spacers are not on the table for me. Is there an...

WTB: Shifter linkage "sleeve"? Not sure what its actually called. It's the metal part that slips inside the bushing connected to the tranny linkage on a manual trans. In my haste to ship out a Hurst shifter to a member, I forgot to remove my stock "sleeve" from the Hurst bushing. I asked the...

I would like to run these two. I think the C&L is the best looking intake but its sheild is cheese. I know the location of the shield's elbow hole is different. And, that the elbow is a different shape, location, and angle but, has anyone done it? The Steeda shield's opening is much larger...

Looking for perfection or close to it. May consider other aftermarket rear bumpers if already painted in Torch red. Thanks, Gerardo

It's actually the CDC rear deck that Ford had made by CDC. The only difference is a FR500 removal rubber "sticker". I'm certain it can be removed without issue. I can move it with my finger pretty easily. Asking $130 shipped to the 48 states. Gerardo Uploaded with ImageShack.us...

I'm selling a SCT tuner locally. I noticed in the manual that it reads "The XCalibrator 2 SF will currently work on the following vehicles:" "Mustangs/Cobras 2006 to 1996" The buyer owns a 2008 GT. Can the tuner be updated or something to flash newer Mustangs? Thanks, Gerardo

Just one. May buy a pair but can't do a set right now. Would prefer local seller as shipping is through the roof. Let know what you want for it. Gerardo 713-203-8346

Has any one tried this? I have them on some 2001 Bullitt seats in my '91LX and they look killer. A friend traded me one for lunch yesterday. After a good wash, an alcohol rub, and a few coats of vinyl paint, this is what I got. I've searched for pics on the Net but no dice. I also have no...

Hello all, Its not technically a DIY but more of a "FYI" and "What do you think about this?" I bought my GT new and had the dealer install the "Shaker" cai. I've wanted to black out the hood since I bought the car but never wanted to spend the bread on a paint job. Then, this free black hood...

Hello all, I was cleaning out my computer room and I stumbled upon some Pony Package fogs I bought last year from JDM. My intent at the time was to try to fab a Shelby grill out of them, some crinkled SS mesh, and the stock OEM grill. Well, the crinckled SS mesh proved too much coin for me and...

I thought about bidding on it too but forgot to come back to it... http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=220678917878&viewitem=&sspagename=STRK%3AMEWAX%3AIT Gerardo

Can be any length or width but the opening to the MAF has to be 4". Looking for something like this. Also looking for a coupler for the throttle body. Any color but red. LMK what you want shipped to 77041. Thanks all, Gerardo

No scratches or broken ANYTHING. $60 plus shipping. Oh, no, I do not have black a/c vents to sell. They're on MY car now. Gerardo