Recent content by 95ragtop

  1. 95ragtop

    Oil Breathers Uneven?

    There is a one way valve within the valve cover of the driver's side valve cover. This valve only allows air into the motor, not out. To remove it you need to pull off the valve cover and cut into it.
  2. 95ragtop

    Give my build list a once over

    Appreciate it guys. The short block is using a stock crank, Boss rods, and wiseco pistons with an 11.0 compression ratio (yay with e85, boo for 93). Heads are FRPP/Livernois stage 3, Comp 127350 cams, and C&L intake manifold. I have every intention of spinning it to 7k. The novi I have is a...
  3. 95ragtop

    Give my build list a once over

    I am going to order some parts tonight and would like to know if you guys see if I am missing anything. I have a short block sitting on an engine stand that I would like to build over the winter and swap it next summer. I already have heads with upgraded valve springs. I plan on reusing my stock...
  4. 95ragtop

    WTB TR6060 Shifter Link Pins

    Here's some I found on eBay. https://www.ebay.com/itm/PIN-Ford-7R3Z-7314-A-/272753110765
  5. 95ragtop

    Mating TR6060 to B326

    The only difference in the 2010+ trans is different 5/6th gears for better fuel economy. There were differences in the throwout bearing and clutches, that's why 2010+ are listed differently. As long as your flywheel and clutch are the correct size you can use them together. What you have...
  6. 95ragtop

    WTB: 3V 3L2E bare block

    I posted brenspeed's eBay store in my quote, not sure why it's not posted, but that's were I saw all 3.
  7. 95ragtop

    WTB: 3V 3L2E bare block

    3 available, 7 hour trip one way
  8. 95ragtop

    Black Friday Buying - need advice on clutch

    The stock 5 speed is a 10 spline. Are you building or swapping the trans because most upgrade to a 26 spline. A stock trans isn't going to last long with 650hp.
  9. 95ragtop

    4.6 3V Whipple - wants to swap Shelby Engine

    Did you buy the gt500 off copart?
  10. 95ragtop

    5.4 3v short block

    For the long tubes, they may fit. I helped a guy with a 5.4 3V swap and he used 4.6 long tubes without any modifications. I have heard that 30 over on mod motors isn't recommended due to the bore spacing. I'm not an engine builder, so if someone with more knowledge than me says it's good...
  11. 95ragtop

    HELP! How do you keep the flywheel from spinning while doing clutch swap?

    To torque my flywheel I threaded a trans bolt and a clutch bolt that went to the outside of the flywheel and used some string to anchor them together. Once I put the clutch on I only needed to add a little manual pressure with my hand to torque it down.
  12. 95ragtop

    Blow thru setup

    Maf location https://imgur.com/gallery/vz0wr
  13. 95ragtop

    forged .20 over pistons

    Jdm used to carry some and I believe mmr too.
  14. 95ragtop

    paxton pulley question

    The rib count shouldn't matter. I plan to run an 8 rib 10% overdrive with my stock 6 rib serpentine. Currently I run a 3.4 pulley and the idler pulley is in the top hole.
  15. 95ragtop

    Intake question

    I know you just got it running and tuned, but VMP is having a sale. 2k for the 1.9L http://www.vmpperformance.com/VMP-1-9L-TVS-upgrade-kit-for-05-10-Roush-Stage-3-p/vmp-19tvs.htm
See more

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Sponsor Links

Banner image
Back
Top