Search results for query: *

  1. Racer45

    What in the actual F would cause this!?!?

    Bling bling
  2. Racer45

    What in the actual F would cause this!?!?

    You were right, there was some play in the crank gear. About .005” to .010” back and forth. Just put on all the MMR parts this morning and there damn solid Thanks for pointing that out for me.
  3. Racer45

    What in the actual F would cause this!?!?

    Thanks for the recommendations. Im not even going to bother checking it. Just put in my order for -MMR billet crank gear -MMR billet trigger wheel -MMR billet chain guides Putting a lid on it till those parts show up
  4. Racer45

    What in the actual F would cause this!?!?

    Thanks for sharing your experience. That checks out for me No. My chains where still tight. One of my tensioners failed and go stuck fully extended out to. No 2 step on the car. But yes I hit my limiter very often when its not worth up shifting coming into corners Think this time around...
  5. Racer45

    What in the actual F would cause this!?!?

    So I was tearing down the motor today cause I assumed one of my chain tensioners seal blew out. “Was not the case” what actually happened was my new tensioner on right bank got stuck open. Completely frozen in place. Would that just happen some times? Second would it cause the crank trigger...
  6. Racer45

    Remove Chain Tensioner Sealer?

    They supply the tensioner clips because felpro probably assumes most people probably lost, threw out or never had any clips at all if they still have the “from factory tensioners” still in the car. Trying to reset your timing without the clips would be a total pain in the ass with out them even...
  7. Racer45

    Remove Chain Tensioner Sealer?

    Well I’d say the proof is in those photos you shared. Can definitely tell the 2 seals arnt going to play nice together imo
  8. Racer45

    Remove Chain Tensioner Sealer?

    yes! You would then peal off the factory bead to get a nice clean flat surface to use this gasket. Same gos for if there brand new as well. Tear off the factory seal Doesn’t matter if there new or old. Run the felpro gasket on its own I Think ill be a good Guinea pig for this product...
  9. Racer45

    Remove Chain Tensioner Sealer?

    If you read this carefully it implies this is the solution to “REPAIR your old tensioners when OEM states to replace if bead is compromise” they state this is the solution for REPAIRING Also states no need for any RTV Im going to throw it on dry my self and leave it at that no bead no RTV
  10. Racer45

    Remove Chain Tensioner Sealer?

    You think just smearing some RTV to fill up the channel would suffice? Because me personally I’m planning on removing the silicone all together my self. The silicone tears and breaks open in my case and that’s proven
  11. Racer45

    Need car fixed ASAP. Any recommendations and experience with this issue would be appreciated

    Right on thanks for confirming the part#. Yup they match up. I’ll have them by Saturday and hopfully back on the road by Sunday
  12. Racer45

    Need car fixed ASAP. Any recommendations and experience with this issue would be appreciated

    Well thanks for the suggestion anyways. I’ll order them up and hopefully this will be a permanent solution to my issue
  13. Racer45

    Need car fixed ASAP. Any recommendations and experience with this issue would be appreciated

    Well if it looks and sound like a duck right. Yeah the pump I got is only hi flow. Not high pressure so think it just moves more GPM at or around the factory pressure. I don’t have a gauge for pressure yet on the car so can’t verify for sure. But you would think running at higher RPM its self...
  14. Racer45

    Need car fixed ASAP. Any recommendations and experience with this issue would be appreciated

    Oh ok I had no idea you could even aftermarket gaskets for those things I’d definitely give those a try then are these the ones you talking about here?
  15. Racer45

    Need car fixed ASAP. Any recommendations and experience with this issue would be appreciated

    The seal was the one that comes glued to the factory plastic chain tensioners so OEM, they came with the ford racing timing kit I threw in the car Drivers bank blew out side that get oil first Oil pump - Melling M360HV hi flow I’m also running a little thicker oil 5w30 And spin the motor...
  16. Racer45

    Need car fixed ASAP. Any recommendations and experience with this issue would be appreciated

    SOLVED. New plastic chain tensioner seal blew out.
  17. Racer45

    Need car fixed ASAP. Any recommendations and experience with this issue would be appreciated

    Yes, it’s a new PA performance 200ah alternator. W upgraded power wires + ran ground 4ga ground cable directly from case bolt to car main ground on passenger strut tower. Battery charges within the specifications I got the alternator out right now also measured the rectifier bridge diodes...
  18. Racer45

    Need car fixed ASAP. Any recommendations and experience with this issue would be appreciated

    07 GT went to ford earlier today and grabbed all new solenoids, cam sensors and crank sensors just installing them all on the car now . Cars @ 120,000mi and it still has all the original stuff on it. Plus the engine harness is getting pretty dumpy lots of Broken connectors, brittle, and been...
  19. Racer45

    Need car fixed ASAP. Any recommendations and experience with this issue would be appreciated

    Went to the track this morning haven’t fired the car up in about a month. Cars power band was stuttering all day didn’t have full power. Knew something was off. Pulled these codes, while I was at the track. While there I pretty much went through the whole harness pulled all the plugs checked...
  20. Racer45

    How would these fit?

    I second this. I’d highly suggest putting your money towards lighter wheels. You’re leaving a lot of performance on the table going with these. Ideally you would want to be looking in the 20- 25 lbs range. Have you checked out other manufacturers Like apex wheels or anybody else? I got a...
  21. Racer45

    Swapping final drive gears In automatic trans cars?.

    Thanks for the input. I’m guessing Your still using stock stall converter and it still made a noticeable difference. Awesome! Thanks you for sharing that’s pretty much what I was looking to hear. Where you get your tune from though? And what gas you running?
  22. Racer45

    2007 GT Rear suspension concern?

    If you decide to tackle the job again maybe order up a small tub of “prothane grease” or “ evil energy grease” on Amazon or something. Make sure your suspension is also loaded when you perform the final torque values To Center my axle I just use a long flat edge on the outside of the fender...
  23. Racer45

    What have you done to your mustang today?

    lol that’s some dedication think I blew mine off with compressor some years back. Also blew the sticker off my buddies cover a few months ago. I never once thought of replacing them. Seen some other people online just resolving the issue by putting a mustang badge of some sort in its place...
  24. Racer45

    Swapping final drive gears In automatic trans cars?.

    Appreciate the response. Yeah the automatic car I want to throw my old 3:55s in ain’t cammed. Its just got a cai + tune. Was just wondering if it would even make a difference in a auto car going from 3:31 to 3:55 gears being with the stall converter n all that I’d imagine he would get atleast...
  25. Racer45

    Swapping final drive gears In automatic trans cars?.

    Yea I use all the 7350rpm sometimes. The cams do start to fall off a bit around the 6700rpm though. Lito set the rev limiter to that and I didn’t question him about it figured he set up these cams multiple times so he knows what he’s doing. I told him it’s a race car and it’s to be used for...

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top