Search results for query: *

Shipped!

I sent you a message, if you can paypal the money I can get it in the mail as early as tomorrow. Movers are here on Thursday and I want it gone before then. -James

Sale pending to tomkay

Buy it for later, never know.

Yes, I'm selling it as a set though. Everything listed for sale, I'll even do $600 shipped if I can get it gone. Movers come on Thursday and I rather not move it to the new house.

Bump. These are all brand new parts, never got around to installing them, and I just don't have the car anymore.

I have a McLeod RXT flywheel, McLeod 6 bolt steel flywheel, ford throw out bearing, and flywheel bolts for sale, brand new in box. These parts are for a TR3650, 5 speed transmission and were intended for my 2005 Mustang GT. Parts are located in Augusta, GA. Ordered as a kit from Lethal...

I didnt say anything because it was one comment. I'm not the Gestapo so I let it go. But there is a point where it becomes clear people aren't following the rules; you were that point. Comment wasn't necessarily directed at you, it was telling everyone if they want to argue about what will or...

Statistically, everything will break at some point. Probability indicates how early. Stick to the rules, unless you're looking to buy, move on. Piece is sold. Hope everyone has a blessed week.

Sold!

As of now, I have a member coming to pick it up on Sunday. I inquired about having it welded, but the quote was crazy. Since the housing is cast, and the tubes are steel, they have to be heated up, welded, then slowly brought down together. If you don't do that then the tubes will cool...

It was sarcasm, didn't think I'd have to explain that. Also, not all focus are FWD; the RS is AWD.

Tentatively sold.

I'm in Augusta. Still have it and looking to get rid of it. It wont fit my Focus ST.

Bump

Honestly, the answer to that question is hard to answer. Depends on how you drive and what you're doing. If you drag race and do hard launches, you'll be more prone to breaking your rear end than a person who only does autocross; especially if you run slicks. I bought this because my...

For Sale is a 05-14, 8.8" rear end. 3.73:1 final drive, 31 spline Nitro 1541h axles, Nitro worm gear limited slip differential, Nitro diff. girdle, solid pinion spacer (no crush sleeve), and ARP main cap studs. I bought it in March with plans to install it in my 2005. I got an offer on my...

I have the original shim, measured and have it set up to the original spec. Also, I did use a set up bearing, tearing down isn’t that much of a hassle, just time consuming.

It was disassembled and prepped for powder coat before that was done. Being it had issues to begin with we didn’t think it important to take measurements from a bad setup

I’m rebuilding a 8.8 and I’m currently checking tooth pattern. I’ve checked back lash and I have it set to .011” with maximum allowed at .012”. Tooth pattern is centered between crown and root but is too much on the toe on the drive side and heel on the coast side. Everything I’ve read says I...

So, we think it's the gauge on the instrument cluster itself? Does the cluster get the mileage from the PCM and I can swap any cluster in there?

Just got my car back on the road and the oil pressure gauge on the cluster is pegged out at max. I couldn't find anything on search, possible bad sensor or bad connector? What could cause this?

If you're gonna look at a rebuild I suggest PSE Superchargers. I'm really happy with the work performed on my Saleen Supercharger. I had a broken heat exchanger and they sonic cleaned the HE and re-welded the bracket that broke. They repainted the S/C upon my request for not too much more, as...

Yep that is exactly what it goes to. Thanks for your help!

My car has been apart for some time and now I'm starting to put it back together. I was an idiot and disassembled it while angry and didn't label the plugs. I attached a photo, can anyone help me? It's on the driver's side, on the same loom as the cam position sensor. Thanks in advance.