NEW JDM forged stroker block, dss driveshaft, Mcleod RXT clutch and fly, etc

[cmg427]

Decided to trade in my Roush Mustang and am selling all the parts I was stocking up for my build and a few take off parts.I will accept check or paypal. Paypal will add 3% to purchase to cover fees unless gifted. Location- Frankfort, KY 40601 will meet up if close by and depending on part.


(SPF to Thump_rrr)The biggie is the new still in box JDM 4.6(5.0) stroker block aluminum at stock compression. I will get more details from Jim Jr. as needed but wanted to get this listed. I did not add anything over what they normally offer for a forged block. This is the one rated to 1000hp the E I believe not the EF $4200+shipping (SPF to Thump_rrr)



Mcleod RXT 10 spline clutch still in wrap and box w/ 8 bolt lightened steel flywheel- $1150 shipped



DSS 1 piece aluminum driveshaft NEW- $675 shipped

VMP twinjet 67mm throttle body- slightly used less then 1000 miles- $475 shipped

aeroforce triple interceptor guages. Comes with 2 different faces and bezels and all wiring for 3 guages (special order)-slightly used- less then 1000 miles Red display $475 shipped

Speed of Sound triple gauge pillar charcoal 10-14 used- $90 shipped

Roush cai for Roush supercharged 11-14 or 10 with Roush TVS used less then 1000 miles- $375+ shipping

MGW short throw shifter new in box for 2010 only- $200 shipped

http://www.s197forum.com/forum/attachment.php?attachmentid=49304&stc=1&d=1407197203

 

[cmg427]

Couple more things

BMR driveshaft front safety loop - new in box $80 shipped

Che kmember brace with torque limiters new in box SOLD

 

[skwerl]

Holy crap that's a ton of nice stuff! I used that same JDM shortblock in my Bullitt and it is designed to have stock compression if you use the FRPP replacement heads (with a slightly larger combustion chamber). I used FRPP stage 3 heads which have a smaller combustion chamber and that resulted in about 10.7-1 compression.

Is that MGW shifter for the 3650 or the MT82?

 

[cmg427]

Holy crap that's a ton of nice stuff! I used that same JDM shortblock in my Bullitt and it is designed to have stock compression if you use the FRPP replacement heads (with a slightly larger combustion chamber). I used FRPP stage 3 heads which have a smaller combustion chamber and that resulted in about 10.7-1 compression.

Is that MGW shifter for the 3650 or the MT82?

Thanks for the additional info, MGW shifter is for 3650 Mustang is a '10. Sorry about the Bullitt Skwerl just seen it was totaled yesterday as I haven't been on in a while.

 

[Johnf78]

So the shifter is no good for the 05-09 then?

 

[skwerl]

So the shifter is no good for the 05-09 then?

If it's for the 3650 then it is the same for all 05-10. (edit- this is incorrect)
Smoking deal on the shifter!

 

[Johnf78]

If it's for the 3650 then it is the same for all 05-10.
Smoking deal on the shifter!

Yes. I want it I just want to make sure it is the one for my car. On mgw website it's a different section for 05-09 and 10.

 

[skwerl]

Oops, I just looked and you are correct, I'm wrong. Looks like they made one just for the 2010 Mustang. I'd make a call to George tomorrow and see what the differences are.

http://mgwltd.com/mustang2005_shifter.shtml
http://mgwltd.com/mustang2010_short_throw_shifter.shtml

 

[Johnf78]

Oops, I just looked and you are correct, I'm wrong. Looks like they made one just for the 2010 Mustang. I'd make a call to George tomorrow and see what the differences are.

http://mgwltd.com/mustang2005_shifter.shtml
http://mgwltd.com/mustang2010_short_throw_shifter.shtml

Will do. Thanks

 

[Johnf78]

I just called. The nice lady on the phone told me it is 10 specific and will not work on my car

Bump for a great price on a great shifter.

 

[cmg427]

Bump with some additional info and most items now shipping included

 

[thump_rrr]

As per our PM's I'll take the JDM Shortblock.

 

[cmg427]

Looks like the block is gone and the car will be traded in the next couple days so there is no turning back now. Let's get these other parts moving. I understand hesitancy buying from someone with no trader rating but everything is legit and please check out my bbb rating http://www.bbb.org/lexington/busine...pital-city-painting-in-frankfort-ky-134645217 for the company I own and operate. That also has my phone # on there if you'd rather call or text about any of the parts. Charlie

 

[POCOPOWER]

pm sent on the k member brace.

 

[POCOPOWER]

Thanks for the K brace. honest guy so dont be afraid to buy from.

 

[skwerl]

Thump got a good deal with that short block. I was impressed with mine.

 

[thump_rrr]

Thump got a good deal with that short block. I was impressed with mine.

For the last 2 times we've put mine on the dyno Jim Sr. kept reminding me that it's time to build a motor.

It's been blown since 2006 and at 13-14psi since 2008.
I've put about 75,000 miles on it since the blower was installed and over 2,500 1/4 mile passes.

Now it's going to Ky. this weekend to pick up the new shortblock which is close to 2,000 miles round trip.

 

[Kidd]

Wow I wish I would have saw this before that motor sold! OP is just up the road from me

Congrats on the deal thumprrr!

 

[cmg427]

Bump with lower pricing

 

[thump_rrr]

Just leaving Charley's with the JDM Shortblock.
Great guy to deal with.