Recent content by Diablogt07

  1. Diablogt07

    Clutch Pedal Sitting Too High on 2011 Mustang GT – Anyone Else Had This Issue?

    Yes that's exactly where mine is suppose to sit and you see how the notch in your push is close to the clutch cylinder. The notch on my push rod is further away from the cylinder. I wanna say at least like 4 inches out. That's why I think the a new clutch master cylinder would fix it and not...
  2. Diablogt07

    Clutch Pedal Sitting Too High on 2011 Mustang GT – Anyone Else Had This Issue?

    That's what I'm saying but the sad part is even that high that's just the resting spot. The engagement point is still the same as stock so they would still have to reach that low.
  3. Diablogt07

    Clutch Pedal Sitting Too High on 2011 Mustang GT – Anyone Else Had This Issue?

    I will do that most definitely but do you really think that alone is what making the pedal sit high? What about you l the pushrod? Look at how far extended it is compared to stock length. Is it suppose to stop at that indent?
  4. Diablogt07

    Clutch Pedal Sitting Too High on 2011 Mustang GT – Anyone Else Had This Issue?

    Ya that's true i get that. I just don't think the extention alone is causing the pedal to sit that high. Especially with the pushrod in the first picture sticking out that much at the rest position. Maybe this picture could help see how high it's resting.
  5. Diablogt07

    Clutch Pedal Sitting Too High on 2011 Mustang GT – Anyone Else Had This Issue?

    Ok ya I'm gonna go ahead and do that along with clutch master cylinder to cover all basis. I appreciate the input as well. Iwas extra confused until I did alot of research.
  6. Diablogt07

    Clutch Pedal Sitting Too High on 2011 Mustang GT – Anyone Else Had This Issue?

    I was thinking about getting a stock pedal cover and replacing that extention and then getting a form master cylinder to fix the height of the pedal because of the push rod being too far out from stock.
  7. Diablogt07

    Clutch Pedal Sitting Too High on 2011 Mustang GT – Anyone Else Had This Issue?

    I had a feeling that pedal was not stock at all. What do you think about the pedal height? The pedal itself paralysis literally is about a inch from touching the bottom of the dash. That's how high it sits and that's the resting position.
  8. Diablogt07

    Clutch Pedal Sitting Too High on 2011 Mustang GT – Anyone Else Had This Issue?

    I recently picked up a 2011 Mustang GT with a McLeod street clutch installed, and I’ve noticed that my clutch pedal sits way higher than stock. From what I’ve seen, most stock S197 clutch pedals aren’t this high, so I’m trying to figure out what’s causing it and if anyone else has run into this...
  9. Diablogt07

    How much would you guys pay?

    Ya i was either gonna do that or get a guys on here headers. He has mac headers and prochamber mid pipe and he coated them and he asking 500.
  10. Diablogt07

    How much would you guys pay?

    He said that it is not rust its just from them just being in heat for so long.
  11. Diablogt07

    How much would you guys pay?

    Here are the jba LTH and mid pipe
  12. Diablogt07

    How much would you guys pay?

    I have pics I'm gonna post below of three jbas bc i think they were to expensive as well especially with how many miles on them
  13. Diablogt07

    How much would you guys pay?

    I have a a person selling me some jba longtube headers and a mid pipe. 400 for headers and 120 for mid pipe. They been on the car for like 35k miles. Do you guys think that's a good price? What do you guys think? I already know someone selling a good pair of headers and mid pype for 500 they...
  14. Diablogt07

    ISO gen5 taillights

    Bump anyone?
  15. Diablogt07

    Raxiom gen5 tailight stuck on reverse

    Geez that's crazy indeed. What does it look like?
See more

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top