Recent content by Rpm427sc

  1. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    The blower and intake are very heavy, but also keep in mind the 10rib belt drive (thick aluminium plate) Heat Exchanger, and 5 gallon Water Tank in the trunk, it all adds up. But that's not the REAL issue. The real issue is heat soak. If you ask any race engineer, one of their primary...
  2. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    With all the wiring done in the engine bay, I can start putting parts on the car. I'll be running this instead of the factory PCV system: I also modified one of the fittings so I could use it for the Fuel Pres Reg Next I moved onto the cooling/heater hoses. Turns out the...
  3. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    Now it was time to wire all of the components in the FRPP Controls Pack. As before, I wanted to hide everything, but also have easy access to any fuses/relays etc. The kit comes with a throttle pedal that needs to be used, and is different than the one already in the car. It comes with a...
  4. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    Power Steering Plumbing, High Pressure Side: The P/S pump was moved to the passenger side, so the stock lines would no longer work. The rack also doesn't have any threads in it, so short of welding on some fittings, I was stuck making the stock hardlines work. So the plan was to cut...
  5. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    Engine Harness mods: Power Distribution: I finished up a few small things, and tested all the non power train circuits with success!
  6. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    Next up was the Fuel System. The FRPP Controls Pack require a stand alone return style system. I settled on a kit from Lethal Performance. The parts I chose will make the whole system 100% E85 compatible as well. 10 Micron Wire Mesh Filter 2 Walbro Pumps PTFE Hoses...
  7. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    Yea, I bought the car new a few months before Ford announced the 2011 model with the 5.0 and the Brembo option. Was sooo pissed haha.
  8. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    Early on I decided that I wanted to keep Hydraulic Power Steering as opposed to converting to electric. I searched around and found a kit from Power by the Hour (Which I ended up regretting) I found out the F-150 Front cover wouldn't work, so I picked up a new cover for a 2013 BOSS, I also...
  9. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    I spent the next 18 months or so chasing Drug Smugglers, Human Traffickers, and Pirates all over the Caribbean, and sometimes even getting a day or two off to explore some of the tropical islands scattered about, usually involving Rum and a Beach. It was such a sharp contrast between the...
  10. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    Once everything was cleaned and thread holes chased, It was time for assembly: One of my Favorite Pics of the build: Ready to go in, American Racing Headers 1-7/8 x 3in Headers Now onto the most tedious part of this whole project: the Wiring! If you look back at the old 3V...
  11. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    My first step was to pull apart the 2011 Coyote Core and see what I had to work with. I stripped the engine down to the bare block and conducted a thorough inspection. Internally the engine looked very clean, and almost no wear. I took the opportunity to detail the block a bit, and...
  12. Rpm427sc

    2010 GT Coyote swap for HPDE/TT Build

    I wanted to share sort of a photo journal of the progress I've been making on a current project. I am not going to get too in depth technically, but I will gladly share any information that I have collected and problems I have solved during this learning process. This is just a hobby for me...
  13. Rpm427sc

    M-2300-T brakes, will forgedstar cf5 19x10 wheels fit

    Wheels are APEX 19x11 ET52 Anthracite EC-7's. I bought the Ford Racing Hub kit w. ARP studs pre-installed, they are around 3in. It took me a long time to find those wheel spacers, I was almost ready to settle for the Eibach pro spacers and knocking the hardware out that comes with them. The...
  14. Rpm427sc

    M-2300-T brakes, will forgedstar cf5 19x10 wheels fit

    I'm running 305's on a 11in wheel (a little wider then yours) and they fit inside the front fenders with a small amount of Neg Camber. ET52 Offset w. a 15mm spacer works for the front and allows them to be moved to the rear with no spacers, hence the extended studs.
  15. Rpm427sc

    M-2300-T brakes, will forgedstar cf5 19x10 wheels fit

    Apex 19x11's on all 4 corners, with S550 15in prem package 6 Pistons Calipers on a 2010 GT. Tons of room.
See more

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Sponsor Links

Banner image
Back
Top