Recent content by SeaWeed

  1. S

    Alternator Drag

    Im in need of some guidence in regards of alternator 05 to 09 6g single phase 135amp vs the 2010 Denso alternator. My Car is still on oem motocraft at 146k miles. Im long overdue ( battery light occasionally flashes randomly.) An about 16 check engine dtcs Checked connections an battery is...
  2. S

    2006 GT Front caliper mounting bolt?

    Good to hear sometimes its better to pay now rather than later. I would get parts list that way u know for future reference parts number. Peace of mind is worth its weight in gold.
  3. S

    Key programming

    Lol my fault sometimes topics get changed but as long as questions get answered thats all that matters to me. Stang bonding is brotherhood!
  4. S

    Key programming

    The remanufactured caliper from vatozone brake line bolt was wider an shorter it was 11mmx1 an threads on caliper looked to be bored out to fit the 11mmx1inch oem was 10x1.5inch fine thread. The first caliper wouldnt seal but i got lucky on second even tho it was different than oem I spent alot...
  5. S

    2006 GT Front caliper mounting bolt?

    Manual for 06 item #5 part number W7095872-S439 Brake caliper anchor plate bolts (2 required) 115Nm (85 lb-ft) torque. I reused my old ones an took wire brush to threads cleaned with brake cleaner, Pb plaster an degreaser. Then reapplied blue loctite on bottom half threads ( i remember old post...
  6. S

    2006 GT Front caliper mounting bolt?

    Message me if u need exact parts number. I own 2006 service manual an will send u pics of diagrams an procedures. I was in same boat as u but i just got done today. Upgraded to 12.4 gt rotors upfront an calipers. I blew the front driverside piston out an chipped them. Centric 120s on all fours...
  7. S

    Key programming

    I didn't start thread bout programming. Was in need of help an was frustrated (been awhile since i got my stang on the road)But i took care of it today thank the Stang Gods! But thanks for your professional advice on programming (knowledge is worth its weight in gold).
  8. S

    Key programming

    Bottom is oem. An the crush washers wont seal because the caliper threads are wider. Autozones remanufacture has done this to two other calipers.
  9. S

    Key programming

    I have an issue with my front passanger caliper. I blew out my driverside piston so i replaced it. As safety precaution i did the other one. The remanufactured one from autozone threads are different 11mm an is shorter than oem10.
  10. S

    Key programming

    Juice u worded like an OG!!! The only thing i wondered about was the doorman product Ignition Lock key cylinder that comes with programing dongle. I haven't had an issue yet.... knock on wood. But out of pure curosity was intrested. The only problem with mine is the faceplate of the cylinder on...
  11. S

    Key programming

    Or buy new Pcm with 2 new keys. You can buy a blank key with new rf chip at local locksmith for 12bucks each JMA FO-30DP Mexico. Just buy 2 an tell Ford u found 2 blanks from previous owner. An just pay for programing if they let u.
  12. S

    Key programming

    If u dont have at least one good rf chip in key ur screwed. I own 06 service manual if u need procedure. Last year my key snapped an i freaked out ( Couldnt find my second) the locksmith replaced with new shell an popped my old rf chip. You can program up to 10 keys an 2 Fobs
  13. S

    Going to put my head in the oven...jk my s197 v6 has been sitting for 2-3months due to pads...

    Going to put my head in the oven...jk my s197 v6 has been sitting for 2-3months due to pads rotors grinding so bad. Jcwitney sent me wrong centric 120 rotors shafted me 100 for shipping. Finally summit did me great only problem is front caliper pistons chipped one blew. So i went vatozone route...
  14. S

    Going insane

    Going insane
Back
Top