Recent content by Skips

  1. Skips

    Can't get camber close, even with camber plates and bolts.

    Thanks. The lower control arms may be original and I will look into that. I was able to get the camber in spec with my basic gauge after reloosening everything pulling the strut out double checking to make sure the camber plate was assembled correctly and just readjusting the camber bolt. I putt...
  2. Skips

    Can't get camber close, even with camber plates and bolts.

    Correct and are supposed to add another 1.6° of adjustability yet I still can't adjust my Camber to under negative two. The only change I made were the struts. I double checked the part number on the struts and they are the correct ones for the s197. I'm at a loss here.
  3. Skips

    Can't get camber close, even with camber plates and bolts.

    Are you specifically talking about the Maximum Motorsports Camber plates? The directions tell you to have the cut out in the camber plate facing out. If I face them in will the larger caster stud still lign up?
  4. Skips

    Can't get camber close, even with camber plates and bolts.

    Camber bolt is in the top hole. The car has neve been in an accident. With the previous struts I had no problem getting it in spec. Car seems a little lower now than it was, I wonder if my springs have compressed since I installed the old struts and had the camber done and alignment. They are...
  5. Skips

    Can't get camber close, even with camber plates and bolts.

    I Changed the front struts on my 2006 GT from the American Muscle brand SR to Koni Orange STR.T struts. Ater the change using my Amazon camber gauge, I cannot get any positive camber at all only negative camber out of spec. 2.0 to 2.5 negative. (Should be -.5 to -1.5) I have Maximum Motorsports...
  6. Skips

    Best shock strut combo for lowered car?

    I did trim the bump stops.
  7. Skips

    Best shock strut combo for lowered car?

    My car is lowered one and a half inches with BMR springs. I have SR struts and shocks in it now and although the ride wasn't bad when I first installed them 3 years ago, it bottoms out and is very harsh now. I'm looking for a strut shock combo that will give a smoother ride with the car being...
  8. Skips

    HT0 plug replacement

    Been using HTO in my 2006 Paxton Novi 2200SL supercharged mustang gt.for 4 years now. Just changed the old ones and they came out ok and looked fine
  9. Skips

    Wide Band sensor cross reference .

    My Innovate wide band A/F gauge calls for Bosch LSU4.9 sensor.I have been getting E8 error code. I tried re calibration but still get the be code after driving a while. Any one use a different sensor than the Bosch with good luck? There are others that cross reference for less $ , just curious...
  10. Skips

    Stock bottom end, boosted, suggested redline for Dyno pull?

    Hey folks. I have a stock bottom end with a novi 2200sl long tubes and catless . Gonna do a dyno pull in the near future . What what have others used that were boosted with stock bottom ends use for rev limiter setting on their dyno Pull? Right now I have my red line set low (6075) for...
  11. Skips

    Oil catch can Question for Paxton SC. Suggestions?

    Thanks. After some more thought I am going to do a vented breather tank. Any oil will have a place to collect and both sides will be vented.
  12. Skips

    Oil catch can Question for Paxton SC. Suggestions?

    I did order the CFM oil cap breather with the check valve, it's just not here yet. I am also going to install catch can with the check valve. Does the the oil line with the check valve go to the intake?
  13. Skips

    Oil catch can Question for Paxton SC. Suggestions?

    Paxton Novi 2200SL with air to air intercooler.
  14. Skips

    Paxton Novi 2200SL Supercharger pulley question.

    Because it has not been dynoed yet, and because I really only beat on it occasionally, (I'm 65 and heading for retirement so $$$ when it breaks is an issue) I'm gonna proceed with exhaust upgrades but forget about the pulley for now.
  15. Skips

    Paxton Novi 2200SL Supercharger pulley question.

    Thank you, good advice. I was just trying to see if somebody else had done that. So I don't have to pay for a tune now when the headers and exhaust or added and then pay for another one down the road with the pully change, figured I would get it all done at once. But I like your advice probably...
See more

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top