Recent content by TANN3R_

Hello, When I bought my car two years ago, the car had a slightly bent axle shaft (half shaft). The previous owner had to hit something.. So I went bought the Richmond axle shaft kit from Rockauto and replace it. Everything was good until last few days I start noticing squicking noise again -...

hello, I planning to lower my 05GT with the Eibach pro kit. I just can´t find the rear spring insulators. Is there some eshop, where I can get them? Now I have the H&R coilover kit on car, wich I already bought with the car, so I don´t have the original factory insulators.. Thank you in advance.

I did little research on the internet and it seems to me that everyone who had problem with fallen ground electrode have problem with combustion gas leak around spark plug too. So that make sense for me.. So I will use it anyway and check them after few hundred miles. This is how looked every...

I know that Autolite spark plugs were welded long time before motorcraft did it. And yes, from what I can find on the internet, they had some issues with the ground electrode that's sometimes fall into combustion chamber. But in most cases there were blower on the engine.. So that make sense due...

Hello, I have a question about Motorcraft spark plugs SP547. Specifically, I want to ask about ground electrode, that is welded on the spark plug. I used an older revision last time that had the barrel with ground electrode made from one piece, but the SP547 should be the latest revision.. Is...

First of all, you need to replace timing chain tensioners, because they cause most of all problems at valvetrain at all. Specially at the passanger side head, because this head get starved from oil first. Most of all problems with roller followers and lash adjuster are caused by bad tensioners...

Midlife Crises: eighty6gt answered my question, not the author of this topic.. And I have "only" 80k miles. I understand both ways - replacement of only damaged parts, or just about everything while I'm there. Because I have still relatively low mileage and not much visible damage on timing...

That is not for the 3V.. This is the right kit I think. But don´t know if it is original Ford parts or aftermarket: https://www.ebay.com/itm/Ford-4-6L-3V-Camshaft-Drive-Kit/193253637241?epid=1578501842&hash=item2cfed07c79:g:FKYAAOSw3I9d8mw4#rwid

Thank you. I would like to stay back from "while you're there":) Because that's how I can exchange everything right away .. Replacing just tensioners and seals will cost me about 200 USD, but the whole timing kit (without oil pump) with tools is at least 1400 USD (post and charges to...

Hello, I apologize in advance for my English. I'm from Europe and I don't use English much .. I just took my timing cover off to check the infamous chain tensioners. I'm glad I did it, bacause the gasket on both tensioners is blown.. I'm going to use the Melling oem plastic style tensioners...

Thanks

Or does someone know what type is the fitting there? Is it type with O-ring, or it is cone seal? Which of these types is used on this pump? To release nut on my pump and look at the fitting I need to put back timing cover back on engine and then reasemble the pump, but I´m waiting for timing...

Hello, I apologize in advance for my English. I'm from Europe and I don't use English much .. Today I removed pump from timing cover, just because I started with timing chain job. Once i put my hand on steering pump hose and release the hose holder drom steering pump, I got surprised how...

Hello, Does anyone know how much play can axhle shaft have in up and down dirrection? I know there is specified maximum end play (in/out) in workshop manuals, but I can´t find the "radial" specification.. I'm trying to find out if my bearings are worn out, without having to disassemble the...

Anti: The whole car looks amazing! Fitment is perfect and the red color is the best color for S197 for me. Thanks for photos.