Recent content by Tinkertech

  1. T

    Best ecm/pcm replacement for 06 GT

    My 2006 GT 4.6L had a bad ecm. AC intermittent, mil light on, O2 heater DTC fault. The ecm had a bad solder joint inside. Could not find a really good replacement so I troubleshot it myself. Located the bad solder and reflowed. This is a common issue with these computers. Google it. The...
  2. T

    Need New PCM ?

    Well its been almost 2 weeks since I repaired my PCM that had the bad solder connections on a 48 pin QVN chip. I could never get a really good ides of what kind of chip it was even though I had the P/N. It seems to be a proprietary design by Motorola who also makes the board. Very little data on...
  3. T

    Need New PCM ?

    UPDATE: I think I troubleshot the issue down to 1 chip on the PCM board. I always felt it was an intermittent solder connection on this board some where. Since I have an extensive background in electronics I gave it my best guess. The board is a real nightmare to work on, no schematic or any...
  4. T

    Need New PCM ?

    How did the Oriellys Cardone rebuilt computer work out for you. Were you happy with the quality of the unit?
  5. T

    Need New PCM ?

    Can you program your old PATS keys from your old bad PCM to a rebuilt FS1 PCM that does not come with keys using Forscan?
  6. T

    Need New PCM ?

    Did you have good luck with FS1?
  7. T

    Need New PCM ?

    I think that I have troubleshooted it down to the PCM. Since I'm in this situation, here is the question I'm after. What I'd like to know is who has gone through the process of buying a used or rebuilt one and what experience did you have. What vendor, good or bad experience?
  8. T

    Need New PCM ?

    All other systems function normally, no other codes. Car runs normally. Just P0053, P0059 and intermittent AC clutch operation all at the same time.
  9. T

    Need New PCM ?

    Don't believe its the pressure switches. My Autel scanner says the AC is engaged but the output ground signal from the PCM to the AC clutch is not there. Also O2 heaters go out at the same time. P0053 and P0059.
  10. T

    Need New PCM ?

    I've already downloaded the wiring system from that sight. Can't find anything in common with the O2 heaters and the AC control. When the AC goes out the PCM does not send a ground signal to the AC clutch relay to energize it even though my Autel MX 808 scanner indicates that the the PCM is...
  11. T

    Need New PCM ?

    No rework on electrical system, all grounds are good. I really wish it was a wiring harness problem.
  12. T

    Need New PCM ?

    I have owned the car since new. Original O2 sensors. Car only has 62,000 miles. These are the pre cat O2 heaters ( 1-1, 2-1 ). They Ohm out good. ( ~ 3.5 Ohms ). I can see the heaters on both drop out at the same time on my Autel MX808 scanner and after a couple of minutes they come back on. I'm...
  13. T

    Need New PCM ?

    Hello everyone. I have been a long time reader but never posted. All my questions were answered by others. I own a 2006 GT 4.6L Mustang, purchased new in 2006, which I believe has developed a PCM / ECM computer Issue. Computer P/N: 6R3A-12A650-XB VK-R3609 S/N: SX4B4K1DWYTS . Issue: 1)...
See more

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top