Search results for query: *

  1. Gavin Eshleman

    Mach 400 clutch

    So my stock clutch finally went on my car and im ordering a exedy mach 400 clutch instead of a mcleod because ive had bad experience with mcleod.Its says its a oem fit but when i got my street pro mcleod clutch it needed to be shimmed which is why i just stuck with stock.Will the mach 400 need...
  2. Gavin Eshleman

    Ticking noise from 1200-1500 rpm

    So my car has developed a weird ticking knocking noise at low rpm with light throttle.Makes no tapping noise whatsoever at idle but if i sit around 1200 rpm it likes to tick.Could this be injectors or something timing related?To me it sounds like its coming from the intake manifold near the...
  3. Gavin Eshleman

    Auto to manual swap with auto wiring harness

    Try this email if you arent already sending emails to this one, [email protected] he doesnt respond just send him another email sometimes he gets spammed and wont see your emails at times.i would advise you to stay away from brenspeed lito is much better in this situation.
  4. Gavin Eshleman

    Auto to manual swap with auto wiring harness

    Theres a thread on here explaining how to use your auto wiring harness.You can use your auto pcm just get a tune through lito and tell him you need it reprogrammed to a manual strategy.You can also use your auto driveshaft.
  5. Gavin Eshleman

    Auto to manual swap with auto wiring harness

    This is what lito has sent me aswell.Hes telling me that i need to run the switch to my passenger kick panel and tap the wire into the 86 pin connector but to be quite frank his instructions have left me lost.
  6. Gavin Eshleman

    Clunking noise in neutral with clutch out

    Stock pressure plate with a aftermarket clutch disk and mcleod tob.I put a mcleod clutch in and it made the same noise just took it out because it wasn't the issue.
  7. Gavin Eshleman

    Auto to manual swap with auto wiring harness

    So i have done my complete auto to manual swap with my auto wiring harness.Speedo works and no check engine lights or limp mode.Just stuck on my reverse light switch and what wire i need to tap it into.I have ran my wire into my passenger kick panel but am lost from there.Any help?
  8. Gavin Eshleman

    Clunking noise in neutral with clutch out

    So im having a real big headache with my tr3650.I manual swapped my car did everything correct.Started the car for the first time with the clutch not bled and it sounded great no clunking or rattling.Soon after i got the clutch bled a horrible clunking noise at idle with clutch out started...
  9. Gavin Eshleman

    Transmission Noise - NEED HELP

    I thought it was pilot bearing aswell but everything checked out on the inside.I emailed my tuner lito about it and he said it’s completely normal for it to be this noisy even when shutting the car off.Would stiffer motor mounts solve it or is it something internal that needs to be addressed...
  10. Gavin Eshleman

    Transmission Noise - NEED HELP

    Had the same issue, when i manual swapped my car i started it up and no noise no clank.Soon after i got the clutch bled the noise was persistent at idle with clutch out.Noise goes away with higher rpm or clutch in.Ive replaced the throwout bearing the pressure plate and the clutch.Could this be...
  11. Gavin Eshleman

    Transmission Noise - NEED HELP

    Did you ever resolve the issue?
  12. Gavin Eshleman

    5r55s to TR3650 swap

    Could you explain how you ran you reverse light pigtail very lost on that did everything else besides that.
  13. Gavin Eshleman

    Complete Auto To Manual swap 2005-2009 Mustang Gt

    Did you ever figure it out?
  14. Gavin Eshleman

    Complete Auto To Manual swap 2005-2009 Mustang Gt

    Could you elaborate on that?I got all the wiring dobe besides the reverse light switch im stuck on that.
  15. Gavin Eshleman

    Need help finding linkage parts for tr3650 for 05-09 gt

    Hey so im having a real trouble finding parts for my tr3650.Im manual swapping it and the linkage part of the shifter is hard to find along with the little knuckle piece that bolts onto the shifting mechanism.If anyone has that part or the whole shifter assembly for a fair price let me know.

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top