Search results for query: *

  1. 0

    Really need some help

    I got some diagrams to verify voltages this weekend. I also just redid the timing with factory phasers, everything spot on same situation, and there's no cats in the car the rear sensors are tuned out, readiness monitors show them as n/a. Bad thing about the tuning is not having a device. I have...
  2. 0

    Really need some help

    So update hooked up another scanner watched some data, maf still high, failed koer test p1101, upstream O2 sensors seem to be acting normal, b1s2 stays steady mid to high voltage as it should if a cat was there, b2s2 fluctuates like upstream. Still yet to find pin hed wires or any sort of...
  3. 0

    Really need some help

    O2 wiring good, gonna get back out there and double check this afternoon. And yea maf reading is extremely high tried a new maf same thing, not the scanner either. I'm leaving towards corrupted tune file, but have no way to verify that. Also the random #6 arcing makes no sense either. No codes...
  4. 0

    Really need some help

    All the harness wires look good to go nothing pinched. I just tore down the front cove replaced tensioners reset timing, marks are lined up as they should be. Start car still runs awful the bad thing is that it's tubed and cammed both are unknown, cannot find out what cams are in the car, all...
  5. 0

    Really need some help

    Sorry for the late response, no car has been tuned for quite some time. Just started randomly about 2 weeks after clutch replacement, verified no pinched wires and no codes
  6. 0

    Really need some help

    Working on an early 08 gt 5 speed. Progressively started running horrible. Has cams, unknown manufacturer or profile, has phaser limiters, comp cams, tuned again unknown by who or what, full exhaust no cats. Car will idle rev up drive etc but has no acceleration like its plugged up. Not...
  7. 0

    Slim fan single or dual for turbo setup

    So I'm looking for some ideas on cooling fans setups. Have an on3 turbo standard turbo with kit stock fan assembly doesn't fit even with leaning radiator forward. Been trying to gather as much info as possible on stock cfm so I can get equal or more flow. I have a shroud but fans are junk. When...
  8. 0

    HUGE partout, everything must go! Everything you need right here

    Maf still available?
  9. 0

    SCT/Air Raid

    Here shortly I'll have all three for sale. Pacesetter Long tubes with h pipe, SCT sf3 handheld, and airaid race cai. And possibly wms 80mm ram air cai kit. Mine is from 07 gt
  10. 0

    First 3v build

    Yea shipping is probably my more than what I paid for this shortblock
  11. 0

    First 3v build

    I already have commitments to the one I'm getting. What would you be asking and where's your location? That's the other issue was trying to find local and avoid shipping charges
  12. 0

    First 3v build

    Cannot locate a reasonable alluminum that's not already short block. Being my first mod motor I'd like to do all of it myself to get a better feel, also the bought over built scenario. The block I am getting is short block so I'll just need rods and pistons to get a good solid bottom end
  13. 0

    First 3v build

    OK so I am planning a build, and wanna get a little more insight on the when situation. Gonna be using a cast iron 4.6 Romeo block, 3v top end of course. Looking to build it capable of handling 7-800 HP, forced induction, for future plans, so a streetable 5-600 to start. Would like advice and...
  14. 0

    Engine build ?s

    Plan on starting a fresh build to handle higher power than the stock 3v internals. Looking for a block now, as to keep car on the road. My main question is what are the main differences between the 2v blocks and 3v blocks. Haven't been able to locate solid answers, except for motor mount...
  15. 0

    3 valve lash adjuster removal

    I saw one write up on google where the guy used a 2 valve but had to modify the tool and part of the head. I'm install the comp cams xfi stage 1 nsr, nothing real wild. And car has 92k regular maintenance adult owned. Just CAI exhaust and tune. But have the cams and ford intake. Also engine has...
  16. 0

    3 valve lash adjuster removal

    Whats the correct part number for the on engine lash adjuster removal tool? I can't seem to get a solid answer from the internet. Keep showing the 2 valve (inexpensive) tool, as being compatible, then show the correct tool. I am installing cams and that seems to be the easiest and fastesr way of...

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top