Search results for query: *

The closer you get to 0degs. of toe ie., no positive or negative toe, the twitchier it gets when driving straight. I had the same experience when I set my alignment to strait up. That's probably true with most rwd cars but maybe not. I had a 91 Camaro RS that I did the same thing to but it...

I understand where everyone is coming from but apparently you don't want to make a track car. You seem to want a car with a more sure footed ride. Age can cause some of the problems you are experiencing so as one person suggested start with the ware items like bushings. Check them for cracking...

Here are two of the three most common water entry points and how I fixed them. First I add aluminum screen on the backside of the cowl cover, this keeps out the leaves and small seeds that fall of the trees next to my driveway, then I removed the deteriorated foam gaskets under the cowl snap...

Just to get this correct you want to disconnect then reconnect the ECM pig tails not completely rewire the harness ends?

Moisture will get in the system even though the smallest of holes. The fact that your system was open for months means you definitely have moisture in the system. The drier is a moisture magnet so it either needs to be replaced or have a long vacuum session drawn on it, the longer the better...

It is of ultimate importance to vacuum the system and to replace the drier. Any moisture in the system can cause a blockage and stop the a/c from working. You will also lose some oil by replacing the drier and condenser. How much I don't know. If you still have the parts laying around you might...

Sorry to take so long to reply, I haven't been on the forum for quite some time. As for making another set I really don't think I could at this time. I don't have the time or the equipment to replicate them now. I'd love to see someone put them into production or at least make a set for their...

WOW. Hope everything inside the tranny is still ok from running it low of fluid. Could that have been the problem with the original trans?

I'm not real sure. My 06 is a manual. I would think a scan tool or a programer that can data log would show gear selection. My be worth starting a new thread on transmission electronics and or wiring. There hast to be a way to tell. The OBD2 port would be my guess too.

Are you sure the trans is actually in first gear and not second or a higher gear when pulling out from a stop? Any higher gear would possibly allow it to roll backwards because there isn't enough torque transfer so it would feel really slow and sluggish. That could be a computer or eleclrtical...

If you look real close, I made the metal backing plate that the taillights are mounted to, is formed to match the curvature of the trunk lid. The stock taillights are not. Even if you cut or took off the red lens portion of it it would be flat compared to the trunk lid. I don't think it would...

It all sounds so simple. And yes I also wanted to do LEDs but couldn't find what I was looking for at the time. I like all the suggestions made by everyone who has chimed in lately. A flat type panel with LEDs behind the lens would solve or simplify one issue but the biggest issue is mounting...

It all sounds so simple. And yes I also wanted to do LEDs but couldn't find what I was l[king for at the time. I like all the suggestions made by everyone who has chimed in lately. A flat type panel with LEDs behind the lens would solve or simplify one issue but the biggest issue is mounting. I...

Which flca's did you end up going with? Can you tell a big improvement? Did you look into the gt500 flca's?

I guess I may may have used the wrong terminology but if you could see what the computer sees. I have a program called Diacom Plus, it's an old progam I can hook up to a mid eighty's and later gm vehicle and see what every sensor is reading. I think all the programmers for our cars are capable...

Do you have or can you borrow a scan tool? That may help you isolate the problem. Hope someone will offer some more help, I know it can be ruff trying to figure this stuff out.

When you say no crank do you mean no start or the engine will not turn over? Have you checked the electric throttle peddle.

Thanks for the like.

Did you find the area or side of the engine the knock is comming from? You may want to take the valve covers off and check all your cam lobes. I had a similar knock and it turn out to be a bad rocker and lobe. I had to replace them. Car ran fine. Don't let it go to long the metal shaving could...

Thanks ExSRT8. I really would like to produce them in some form or fashion. It's just so costly to do it on your own. A large company could do it but the timming may be a little to late. Still, I know there's a market for them. Ken, thanks for the info. I forgot Saleen had the custom rear...

I guess I didn't make myself clear. IT'S NOT A MUSTANG MOVIE BUT MY FAVORITE IS VANISHING POINT. Just saying. I also apologize for hijacking this thread.

It's not a mustang movie but my favorite is Vanishing Point. Then American Graffiti, Two Lane Blacktop. Bullet was good. Grand Prix is another good one. Sorry I guess I'm just showing my age.

Like Jeremy said. What's up. Really thought please explain a little better as to what you really wanted to ask. Something about power or heated seats ?

As much money as all new cars and trucks cost these days and all the companys trying to come out with autonomous driving vehicles it would be a lot cheaper if they just throw in a chauffeur.