Search results for query: *

  1. 0

    Tr3650 hard to shift at a stop

    Not really sure where to go further on this issue. Issue has been getting worse for a while now where if the car is on and at a stop shifting into any gear is damn near impossible. Shifting out of gear into neutral sometimes takes quite a bit of muscling like its stuck too. It used to be mainly...
  2. 0

    Can't get 08 into gear after replacing clutch master cylinder

    not so much greater volume than stock I just believe the worn master just wasnt pushing much fluid and the increase in fluid by putting in a new oe master could have been what was the final nail in the coffin. Either that or the amount of times i had to actuate the slave used up whatever life it...
  3. 0

    Can't get 08 into gear after replacing clutch master cylinder

    It was just so hard to believe that a somewhat working vehicle immediately became undrivable after only replacing the cmc. Looking back I think the new master cyl is what did the slave in finally. Before dropping the trans when I was still trying to bleed it out i noticed a squeak when...
  4. 0

    Can't get 08 into gear after replacing clutch master cylinder

    Hahaha I KNEW you'd be back with an I told you so:biggrin:.
  5. 0

    Can't get 08 into gear after replacing clutch master cylinder

    For anyone interested in an update decided to drop the trans. Slave cylinder fell apart like a toy. Somehow i think that could be related to the issue i had. Clutch doesnt look too good either. Putting in a mcleod as we speak but it's slow work on jackstands.
  6. 0

    Can't get 08 into gear after replacing clutch master cylinder

    Seems pretty similar to what I've been doing except i had the drivers side raised maybe trying it flat is the solution. Using hf vacuum pump and rubber stopper. Plug vac to the master and pump it to 20 in/hg. Pump pedal while its doing this. I do this for about 5 minutes. Release vac and pump...
  7. 0

    Can't get 08 into gear after replacing clutch master cylinder

    That's the part that i don't know. I've put almost 25k since owning it, but its atleast had a job done by the last owner at some point. Clutch looks red like the mcleods. Visually it looks alright and havent had any other symptoms or issues with it. No slippage or noises that i can hear other...
  8. 0

    Can't get 08 into gear after replacing clutch master cylinder

    Yep have the drivers side jacked about 8". All signs point to air trapped still but I'm at a wits end on where from. I can hold a consistent 20 in of vacuum so i don't believe theres a leak anywhere. I did take the new master off and try bench bleeding it by attaching a hose to the output that...
  9. 0

    Can't get 08 into gear after replacing clutch master cylinder

    That's what its seeming like haha but it feels like pulling teeth hearing it:angry1:. Is there any way i can confirm that its all the way bled without lowering and starting it? I'm worried if it does infact have air that it could be stuck in the slave or aerated and it makes it worse that i keep...
  10. 0

    Can't get 08 into gear after replacing clutch master cylinder

    Ive been searching for the answer to this specific issue for days to no avail. Backstory Replaced my clutch master cylinder as i noticed over the course of a week it became harder and harder to get the car into gear when the car was running. All gears felt pretty similar and the issue only...
  11. 0

    cam phasor hitting camshaft position sensor after timing set install

    Did you figure this out? Doing cams right now the detroit rockers and running into the same issue. Pretty sure i got the sides right too. Drivers side phaser slid in easy pass side seems to contact the sensor by abt 4mm

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top