GallopingFord
I'm Cam - Mr. Indecisive
Ah yes, Ryan loves showing off his midriff. #southernboy
Sent from my SCT X4 using Tunatwat
Sent from my SCT X4 using Tunatwat
Project Large Caliber - Cam's NEW 2009 Bullitt Build Thread
- Thread starter GallopingFord
- Start date
Macman45
Resident Geriatric
Cams latest mod.
Oh lawd. What's your insta Ryan? Mine is @ricky_strom
GallopingFord
I'm Cam - Mr. Indecisive
I believe I've settled on an exhaust setup.
Going to go with 2.75" OTA pipes all the way back into 11/12 GT500 mufflers. Going to cut the tips off eventually and weld on the Bullitt 3.5" tips.
It will remain quite and such, but later I will install electric exhaust cut outs.
Going to go with 2.75" OTA pipes all the way back into 11/12 GT500 mufflers. Going to cut the tips off eventually and weld on the Bullitt 3.5" tips.
It will remain quite and such, but later I will install electric exhaust cut outs.
Last edited:
GrnBullitt08
Dale Jr
And install a 3.4L
GallopingFord
I'm Cam - Mr. Indecisive
Figure out how to make the stock hood close over it and I'll do it.
2.3L TVS is most likely the next one.
2.3L TVS is most likely the next one.
Mystickeith50
Senior Member
Cut a god Damn hole in it......
GrnBullitt08
Dale Jr
And zip tie a plant to it... Nobody will ever know
ford20
Senior Member
Or one of those red bows like on them thar Lexus commercials.
Boaisy
Dark Knight
lower the motor.
GallopingFord
I'm Cam - Mr. Indecisive
Worked on it some today
Put in DS safety loop
Hood struts
Finally hooked up boost sensor line
Installed shifter ball - which feels badass
Installed the rest of the trim in the trunk.
Hoping to get it on the road by this weekend. Just need to weld in wideband, tighten DS, and a couple other things.
Sent from my SCT X4 using Tunatwat
Put in DS safety loop
Hood struts
Finally hooked up boost sensor line
Installed shifter ball - which feels badass
Installed the rest of the trim in the trunk.
Hoping to get it on the road by this weekend. Just need to weld in wideband, tighten DS, and a couple other things.
Sent from my SCT X4 using Tunatwat
ford20
Senior Member
Dat DS 
Looks like things are coming along really nicely at this point!
Looks like things are coming along really nicely at this point!
moostang09
Resident YouTube Guy
Good work today cam! What hood struts did you end up going with? This car is going to look "factory stock" when you get done! I'm excited to see/hear the cutouts when those eventually get put on.
shark tales
Wiggle Wiggle Memeber
Uuuhh :Rick Ross voice:
Sent from my iPhone
Sent from my iPhone
GallopingFord
I'm Cam - Mr. Indecisive
Dat DS
Looks like things are coming along really nicely at this point!
Yeah, just need to keep the momentum up. Trying to find a set of mufflers/OTA pipes this week. If I could test drive the thing this weekend I'd be delighted.
I went with the Redlines. I heard a lot of good things and the position of them is much better than the ones that bolt to the hood hinges. So far so good.
I had to look up who Rick Ross is to understand this. lol
GrnBullitt08
Dale Jr
That car is gonna need some serious polishing and TLC after this is done. I see swirls all in the paint
GallopingFord
I'm Cam - Mr. Indecisive
LOL, the paint is absolutely horrible. For a car with only 23K miles it looks like it has been through hell. After I finish the car up this will be whats next -
Fill in the Sat antenna hole/repaint
Fill in fender anntenna hole/repaint fender
Fill in hood washer nozzle hole/repaint
Then full wet sand, compound, etc etc.
Fill in the Sat antenna hole/repaint
Fill in fender anntenna hole/repaint fender
Fill in hood washer nozzle hole/repaint
Then full wet sand, compound, etc etc.
Last edited:
joeymustang
Member
I'm glad that this build is coming to finishing touches and more pics of it outside and videos of it riding will come soon. Looking forward to it!
moostang09
Resident YouTube Guy
Cam are you flying me out to do some video stuff of this car for you?! Lol!!! I would drive but it's so damn far away!
