Search results for query: *

  1. 0

    Boot

    Guys, I have buddy back in Austria that tore the rubber boot on the center joint of the driveshaft. Anybody know if there is a replacement part for this and what the part number may be? He cant get it locally and nobody knows the part number there, Mustangs are an exotic over there..... Thanks...
  2. 0

    Oil dipstick tube

    Ss there a gasket, O-ring or grommet that goes on the bottom of the engine oil dipstck tube? Since the removal and reinstallation for long tube headers my oil dipstick tube is leaking where it goes into the engine block. Anybody else have this issue? :helpme:
  3. 0

    South Jersey Auto Crosse Events

    Hey, the SCCA SJ region is hosting monthly auto cross events at the old Bader Field airport in Atlantic City. Entry fee is $35.00 for SCCA members and $50.00 for non members. Right now there a only a few "Stangs" running and we need some more to beat those pesky imports. The next event is June...
  4. 0

    Help!

    What sieze and thead is the steering nuckle bolt where it connects the shaft to the rack (yes I searched , but nada). I need to put something with a smaller head in because the fucking thing still hits even afer I dented the LT's. Thanks guys
  5. 0

    Bolts

    I just bought a set of JDM motor mounts without the bolts. Anybody know what seize and material spec the motor mount bolts are? Thanks
  6. 0

    Front Wheel Bearing

    Anybody have their front wheel bearings go bad? I got a vibration in the front left side when I go into right turns. I checked all the usual stuff and found nothing. When I jacked the car up and spun the left front tire by hand it binds after about half a turn and then spins for half a turn...
  7. 0

    CAI, UDP's and IPAC

    Only thing left are Steeda UDP's. Set of Steeda UDP's, used for about six + month, installed a SC and can't use them any more. Bolts not included. $120.00 shipped. *****SOLD******* I take Paypal, PM me for info.
  8. 0

    Header Install

    Installing a set of shorty headers next week (just put a off road x-pipe on). Using stage 8 locking bolts, any tricks or anything I should be aware off before I do the install in my driveway? Thanks BTW, before you guys start, the headers where really cheap and will be only on there until...
  9. 0

    Lambo Stang

    I guess this is kinda tech related, get a load of this: http://www.honda-tech.com/showthread.php?t=2726800 If Ford HP is just not enough...................
  10. 0

    Harness question

    Question for you guys always building /swapping out engines. Will an 05 automatic engine harness work on a 5 speed manual (same year)?
  11. 0

    KB Boost-A-Spark Installed

    Well I finally had time to take the car to Tillman to get the module wired (didn't have the balls to cut the wires myself). Well I my case (<-- disclaimer) it worked. The car acts and drives totally different, it feels like it got a lot more power. I am running Autolite HT0's ungapped, the idle...
  12. 0

    Harness

    WTB. Looking for 05 GT manual trans engine harness................
  13. 0

    OBX Headers

    Anybody running these? Problems? OBX been around for a while....... http://cgi.ebay.com/ebaymotors/OBX-05-09-Ford-Mustang-GT-4-6L-Stainless-Steel-Header_W0QQcmdZViewItemQQhashZitem27ad53cfeeQQitemZ170411675630QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories And yea I know Kooks...
  14. 0

    KB Boost-A-Spark

    Anybody running it? pros / cons? This is why I am asking http://s197forum.com/forum/showthread.php?t=24628 It's cheap enough to give it a whirl, maybe that would solve my problem????????????????
  15. 0

    Intermittened power loss (HP)

    This maybe a long story. Anyway, when Tillman installed my Techco blower, the engineer from Techco tuning that thing could not get it to make more than ~420whp @ 10psi. They canged coils, plugs and all that good stuff... nothing. All of a sudden the car made 465whp and everybody was happy but...
  16. 0

    For everbody running a TECHCO blower

    I found a guy in CA that worked for Techco and is actually answering questions about their blower (thanks Russ) I asked him abou the SC oil and pulleys for the TECHCO and got this back from him: Hi Helmut, Tons of people always asked us about the gear oil. It's 75-90 HD made by Neo...
  17. 0

    SC Oil

    I need to get some oil for my Techco Twinscrew. I just noticed that I'm below the half way line in the bullseye. The install manual does not specify what oil, Techco is belly up so I can't ask and Tillman thinks I should use the same oil that they put in the new GT500's blower and get it from...
  18. 0

    Need input

    I also posted this on MM. I'm batteling this intermittend check engine light issue. It started after the SC install, it would trow a CEL light at ~85mph, I get off the gas, coast and it goes away, no codes stored. Back then I had Tillman and Techco look into the issue, the tune was good...

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top