Search results for query: *

I am running lean on one side of the motor causing car to bog down when into the throttle. I have cleaned the MAF and the O2 sensor seems to be fine on the scan tool graph. No codes are being thrown ... Fuel trim is +14 on bank 2 I am going to run smoke through EVAP intake hose and see if I...

Any help troubleshooting this would be great. It’s not the cluster as I have two, same behavior on both. After the car is warm and particularly after highway driving, I come to a stop and Speedo starts to bounce. Start to go and speedo needle becomes stable once again; only bounces at idle. I...

Looking for twin 67mm throttle body for GT500 ; if anyone has evap adaptor for TVS 2.3 trinity elbow, I need that as well.

****Will fit 05-14 S197, can't change title..***** Full suspension with Eibach springs. GC coil overs up front, Koni rear shocks. Spring and Shock part numbers are in pics. I believe they are sport springs. Rear shocks are just missing dust caps , otherwise everything is complete, including...

Just got this bad boy in from Jason. Boy is it purty.

Sold Brand new never run on car. I had this mounted to a motor on the stand and decided to go with a GT500 pan from a 13/14 car. Link to detailed description below https://www.cantonracingproducts.com/product/13-784A/13-784A----FORD-46L54L-REAR-SUMP-ALUMINUM-RACE-BAFFLED-PAN/ Thanks for looking

I know the spec is 30 ft/lbs + 90* , they are TTY, so one shot deal on the bolts , but I feel like I am going to snap these bolts getting to +90 . How hard should I expect to be pulling on these to get to +90? I really didn't want to take all of my followers back out and the chains off to...

While taking out my solid lash adjusters and putting back all of my followers I mistakenly turned the crank while my wedge took was in place on the left bank. The wedge tool I have never really fit all that snug, so the crank moved fairly easily. I never noticed slack in the chain at certain...

Most I can come up with via search are engineering parts numbers. 5C3E-6N881-AB and 53CE-6C743-AB Does anybody know the part numbers without having to cross reference these? I know I can get them from MMR, but does anybody else stock them? Vendors?? Thanks

Looking for an 8 rib standard diameter in an ATI but apparently they do not offer one off the shelf. You can have it special ordered for another $60 however. Innovators West offers the 8 rib in a standard diameter. I really wanted an ATI from the research I have done. You can separate the hub...

Steve, is there a new forum discount code?

Anybody have to trim these fours "ears" off to get an aftermarket oil pan to sit flush? In this case it's a canton 13-784 A . I trimmed them on the old gasket, but before I trim the new one I want to make sure .

Looking for a standard diameter Damper for a 4.6 3V, what you guys got? Thanks

When I did my 6060 there was no shim behind the TB of the tranny I bought, but on my 3650 there was a 1/8" shim behind it. I was wondering what dictates whether you need one or not? I can see the bell housing is much deeper in the 3650, but does it matter what clutch you use? I have a spec 2+...

Barton Shifter, 3650 & DSS for Sale Just got finished with a 6060 swap and would like to make some room for more parts. All prices except the Transmission include shipping + paypal fee. Everything that is included is in the pics. Barton Shifter for 3650 - SOLD DSS one piece...

Any downside to having an aluminum flywheel versus steel with a PD Blower? I was told it was no good because of rotating mass difference etc etc .. I assumed perhaps there was logic there as a PD blower has instant torque:revs versus a centri ... What's the bottom line?? Thoughts Tranny is out...

I searched but could not find much on what the maximum negative offset one could use on a S197 without it extending past fender. Say 305 or 315 on a 10 inch wheel in the rear and a 255 or 265 up front on a 9 inch. I am looking for a semi deep dish look on like a weld, Velgen or Vossen...

Looking for an 8 rib ATI or IW balancer, OE diameter or 10% OD. Let me know what you have

Looking for new transmission for a new motor build.

Let me know what you got. Looking for 13-14 GT 500 heat exchanger , Afco or C/R

Let me know what you have please.

White 1-7/8 diameter Shifter Ball for Sale. $27 Shipped.

I am looking to add an axle brace to my stock 8.8. I have BMR relocation brackets and have heard the CHE brace may not fit. I called CHE, no answer of course, left messages, emails; but no return calls to my questions. 1. Does anybody run a CHE Axle brace with BMR relo brackets. 2. Is there...

I have read the many threads on his subject ( yes I used search)and there are lots of opinions/applications etc..., guys that road race versus drag versus DD, all with different setups. I am looking for optimum application for my setup. I have a twin screw Kenne Bell and today I have nothing...

Anybody have ideas on what/where I can look in terms of upgrading my rear calipers and rotors? I cannot look at the disgusting OEM calipers any longer. I have 4 piston Brembos upfront (black off a GT 500). I was going to paint these red and re-sticker them, so looking for matching red in the...