Search results for query: *

[Sold to Rich07 ; thank you!] Used 1-piece 3-1/2" aluminum driveshaft for Ford Mustangs. Fits 6R80 automatics (and I think with MT82) transmissions. Weighs only 18 pounds! Remove the extra heavy weight of a stock driveshaft. Selling because I am not using it; this driveshaft was included in a...

[Edit: all sold.]

[Driveshaft, B&M hammer shifter, and shifter cable are sold; edited and removed] Selling these from a previous 4r70w installation that was in my 2005: - Lokar flexible dipstick, firewall-mount - $75 - s197 automatic shifter cover (for 5r55s) trim rectangle - $10 Will ship or meet up in...

4.6L 2005/2006 cooling system crossover, thermostat housing with 160* Hyperstat thermostat, hoses, and brackets as shown. This setup can also be used on 2007-2010 4.6L engines (I had it on my 2009 engine). Includes all of the large hoses: crossover to radiator (passenger side), crossover to...

Hydraulic Power Steering cooling line/hose as shown. [mostly sold; I only have the loop-line that sits in front of radiator, shown at the bottom of this pic.] Fits 2005-2010 Mustangs, all models. 55k miles on the rack and lines. No issues, all in good working condition. Removed all of these from...

[SOLD] OEM power steering pump with 8-rib pulley. Fits 2005-2010 GT/4.6L Mustangs. Pulley was laser-aligned with other 8-rib pulleys, pressed-on. No issues, removed as part of my EPAS conversion, and no longer need it. I'll include the mounting bolts/studs if you need them. Located in Central...

[SOLD] Selling my Canton aluminum power steering reservoir (I think the part number is 77-236). Fits 2005-2010 Mustangs. No issues, worked perfectly. Includes the fittings and lid as shown. It is NOT polished, as shown. Removed from my '05 as I no longer am using it.

I was curious, for hot summer months where you're not worried about heater operation (nor emissions): is there any harm or reason to not run with a thermostat? (i.e., delete the thermostat.) There should be higher flow through/to the radiator, instead of the puny little opening a thermosat...

Have a turbo setup on a '06 with a stock maf and a DiabloSport MAF.ia maf extender. The maf.ia is done for, and needs to be replaced. Is there an alternative MAF sensor or something, where no tune changes would be required? Or, using the #2 setting on the maf.ia, does someone have a...

[edit: getting one from freeloader1969. thanks!] Looking for a working MAF.ia device, #F7370 for 2005-2010 Mustangs.

[no longer looking; thanks] Anyone have a decent used 6-bolt 4.6L flexplate for sale or wanting to get rid of (for a 5r55s automatic, 2005-2010 GT)?

[edited: removed items that are no longer available.] Various parts from parting out a 2007 4.6L engine with 82k miles. - timing cover - $40 - oil pan - will include oil pickup tube and 2 lightly used pan gaskets - $40 - oil-filter/radiator-hose adapter (lower-driver-side of block) - $25 -...

***SOLD*** For sale: Battery relocation kit with extra parts and upgraded wiring. - battery box with cover - 1/0 marine-grade main power cable - 1/0 ground cable - 200 amp fuse - two relays (one as used in trunk to feed stereo amps and fuel pumps) - alternator cable (with large alternator wire...

For sale, 6-rib ATI crankcase Super Damper / Harmonic Balancer. Stock size (# 918039). Fits 2005-2010 4.6L V8. Very good condition. Located near Austin, Texas. $300 shipped, $275 local/picked-up.

Selling the following items, all used an removed from a '05 Mustang. All should fit 2005-2014. Prices shown are shipped and include paypal fees. Located near Austin, Texas. [updated, items sold have been removed:] - N2MB WOT box with cables/wiring as shown - $165 shipped AEM Boost Gauge, -30...

[Close thread; no longer looking.] Looking for: - stock mufflers - fuel rail feed line/hose between the fuel rail and hard-line at the fender These are for a 4.6 3v, 2005-2010.

[Found one.] Looking for a good used stock driveshaft for a GT, either 3650 manual or 5r55s automatic, from 2005-2010.

***NO LONGER AVAILABLE *** - removing listing; car is being put back together and is not for sale as a roller at this time. Good 2005 Mustang GT body/roller for a race car, Coyote swap, or simply restoring it to a good street car! No body rust (we don't get salty roads around here in Texas!)...

Looking for good take-off stock headlights, both sides; no broken tabs nor cracks. Must be clear and very good condition. I need both sides, but will consider one side-only if you have a good one for one side. I'm located in central Texas, so would pick-up within reasonable distance or pay for...

[I think I know the answer, but want to hear more opinions from those with experience.] Setup is 4r70w with 3200-3400 rpm circle-d converter, full auto valve body with no transbrake, twin-turbos. I prefer to have a fully-automatic transmisison function with auto valve body (no manual vb)...

Looking for the factory spare tire jack from 2005+. Local preferred, or cheap+shipping.

*sold*

Anyone have some extra RaceStar lugs laying around? Gave one away awhile back, and now I need one to complete my set.

It's been slow in coming, but finally made it out to a 1/4 mile track with the twin turbos. I wanted to get some good solid test-n-tune runs in, figure things out and and dial in a few things, before cranking up the boost. Boost controller was set to 13.5 psi as a starting point (lowest with...

Parchment passenger side seat trim cover and recline handle, for attaching to the side of stock seat brackets. The cover is FREE; just cover the cost of shipping or pick up locally. $5 for the handle plus shipping