Search results for query: *

Used out of my 9" rear end. Motive Gear F890411 9" Rear Ring and Pinion for Ford (4.11 Ratio) - 8620 Steel Performance Differential Ring And Pinion - Ratio: 4.11 Pinion Spline: 28 - Ring Diameter: 9 Pinion Diameter: 1.313 - Ring Gear Teeth: 41 Pinion Teeth: 10 Amazon.com: Motive Gear...

I have a 2005 with S&W's 9" rear end and I bought their anti roll bar kit located here: https://swracecars.com/store/2005-2014-Mustang-Bolt-on-Anti-Roll-Bar-Kit-OSCARItem_238=40-708.aspx The top mount plate welds to the floor pan. I'm somewhat new to drag racing and these types of setups...

Hey guys, Have a few gauges laying around want to get rid of they do me no good! - Autometer pro comp ultra lite mechanical oil pressure gauge $30 shipped - Autometer sport comp nitrous pressure gauge $30 shipped - NOS bottle gauge 40 shipped Not sure what these go for but I feel like...

Hey guys, I have a few Kenne Bell pullies off of my 05 mustang with the 2.6. What I have: - Reichard Racing 8 rib 3.1" pulley SOLD - Kenne Bell 8 rib 3.75" $30 shipped - Kenne Bell 6 rib 3.75" $30 shipped (not pictured) - Kenne Bell 6 rib 3.5" $30 shipped Let me know what you want!

Hey guys, Went to e85 and this is what I had in there before. It was used for maybe 4k miles. I misplaced the float so that is why I'm selling it cheap. You can use the float off your stock pump. Works perfectly. I ran 610 rwhp on pump gas but also had a BAP just in case. They rate just the...

Hey guys, I'm out of town and the car is in not accessible to anyone else. It is getting tuned Saturday on e85 and I wanted to put on a fresh filter as its been a while since I replaced it. I would rather NOT clean it and risk the chance of messing up the MAF from too much oil. I know KB...

Hey guys, I have a used ThumpRRR tensioner off of my 2005 GT. It is in great condition minus where you put your ratchet/belt too, but only cosmetic. The hole is NOT rounded out just the edges of it are curled up. I was going to grind them down and smooth them out but I will let the next buyer...

This upgraded GT500 hat will support 750-800rwhp without a bap. It's a direct drop in replacement for your oem gt500 hat. The Gt500 hat itself is a new takeoff and in excellent shape, the hat is modified by Jeremy from S&H with two lethal divsionx 340lph pumps and walbro filter socks. The pumps...

Hey guys, I have a built 05 and need some advice on alignment specs for the drag strip and also want to know if I'm doing anything wrong suspension wise. I cannot seem to cut better than a mid 1.6 60'. My best run so far is a 11.3 at 124/125 mph with a 1.6x 60'. Specs on car: Quick engine...

Any thoughts on this setup? The guy working on my car bought the kit for me and now I can't take it back. I've heard mixed things with the kit but no one that I know that has personal experience or that knows a lot about these cars anf fuel systems and general. I searched the forum and all I...

I tried searching on Google and on here for about 2 hours and could not find what the specs are on the stock radiator fan. Trying to decrease under hood temps.

Hey guys, I'm getting a triple pump setup from On3 for my 05 mustang (keep the hating off the thread, Chad is local to me and I've known him for a while). I have a 2.6L kenne bell. I'm probably going to go turbo this winter, but want to see what I can do with my Kenne Bell and some e85 since...

Taking my dual gt500 setup out and need the wiring harness out of an 05 asap Sent from my SCH-I545 using Tapatalk

Hey guys, Tried PM'ing Jeremy, since he is who I was originally working with when I bought the pump, but says he can not receive PM's right now...? Anyways... I bought this pump setup from you guys: http://www.s197forum.com/forum/showthread.php?t=98794 I previously had a GT500 fuel pump...

Car had a start up tune put on then it slowly started running like crap from what I was told and lost fuel pressure. This is the pic I got from the shop. Is this a common problem? And sorry, I'm not sure what the technical name is so I just called it a y fitting. Looks like it broke up in...

Like the title states, I have a set of 15x10 and 17x4 unilug Dark Stars. The rears were mounted, then removed. They would not work with my setup (because they are unilug and my new rear end/axles do not have centering hubs, I needed direct drill to be able to center the wheels I guess) There is...

Probably one of the best mods for your car to improve your acceleration. I've had this on my car for maybe 4000 miles. I would NOT be selling it, but it does not work with my new 9" rear end, so unfortunately I had to go a different route. It is 4", Alum. and weighs about 30 pounds less than the...

Hey guys, One dilemma after another. I should have just built my 8.8 :handjob: Anyways... Shop finally got the rear end together after finding the right retaining plates and getting my new true trac in the 9", got the stock brakes on and everything. Now, the hub does not stick out any...

My unilug racestars will not fit with my new 9" rear end. The axle hub does not stick out at all from the rotor to use the hub ring and since they are unilug, it is impossible to center the wheels without the hub ring on. So, I need something drilled specific to mustang's (5x4.5) I wouldn't...

I went with the black chrome instead because matching fronts were almost the same as the whole set of black chrome, so these are now for sale. They were on the car for maybe a total of 2000 miles. I only have one pictured, but it is for the pair. Nothing is wrong with either one. So two 15" x...

SOLD Kenne Bell 2.4L Supercharger Ok guys, I have for sale the supercharger for my car. I got something a little bigger and do no need this anymore. My last power level was 599 rwhp and 575 ft lbs of torque using race gas and about 16-17 psi (but I have other mods also). The s/c treated me...

This is from my original dual gt500 fuel pump kit. I got a larger fuel setup to meet my new needs so I'm selling this. This pump only has a couple thousand miles on it and I can get the exact mileage if needed. I know for sure there is not more than 4k but no less than 1.5k. I tried to take pics...

Diablo MAFia 96-04 Ford While going from a 2.4L KB to a 2.6L KB, I also got a new maf so I no longer need the MAFia. It literally only has a couple thousand miles on it and maybe two years old. Works great. This is for 96-04 Fords!!! $100 shipped

As of right now I need two parts: - FRPS spacer (relocates the fuel rail sensor slightly so it clears the bypass valve) for my 2.6 install - ECU relocation bracket to sell with my 2.4L KB kit Pm me with what you have

Have had this sitting around for a year or two and just need it gone. Sells for $450+ everywhere online, looking to get $250 shipped. This is said to fit 2001.5 and up Mustangs and Cobra's (4.6 and 5.4) and it is 164 tooth. $250 shipped