Search results for query: *

Pair of custom ground naturally aspirated cams from Comp. Never been out of the bag. These are MD540 series lobes intended for racing as recommended by Billy Godbold at Comp. Gun drilled cores. Require phaser lockouts, springs and ported heads would be good. Going in a different direction with...

Sorry, posted in the wrong forum. Please delete.

Does anyone have the full pinout schematic of the 3V ECM they can share?

Occasionally my fuel gauge goes from 1/4 tank to zero in an instant. I put an Aeromotive Stealth pump in last year and the problem has come and gone since. I've had the pump in and out a couple times trying to find anything obvious but everything is connected and appears normal. Thoughts? CSR

I'm starting to part my car to turn it into a drag car. All parts listed were purchased new and have less than 5k miles on them. 2007 TR3650 trans. Includes: New 2nd gear and synchro hub supplied from Pro-Force Performance All new synchros supplied from Pro-Force Performance Bronze shift...

Finally getting some miles on my car for the year. I put an Aeromotive Stealth fuel pump in over the winter. Heavy acceleration is causing a zero fuel pressure condition for a couple hundred milliseconds at a time per the data log. I noticed it yesterday at lunch and then logged it. Less...

I will likely eliminate my A/C this year and want to move the alternator to where the A/C compressor used to be. Is anyone aware of a bracket kit to do this? CSR

Just need the center section. No ring gear, no bearings, and I don't care if it has gears or not. Looking for something cheap and serviceable.

Looking for a JW ultra bell or similar to bolt a C4 trans to a modular motor.

Looking for suggestions on lightweight front brakes for a 2007 Mustang on a budget. CSR

Is there a max fuel pressure that the stock fuel pump can provide? I've been watching my FP on some data logs while tuning and have seen ~55psi thus far. Just curious if I'm nearing a fueling limit.

Green connectors are upstream and blue are downstream correct? I failed to take not when I took everything apart it seems and my leads are long enough to reach either location.

Like the title says, I'm looking for a stock or stock diameter water pump pulley to fit a 4.6L 3V.

I'm working on tuning and have noticed that the coolant temp on my car has been running in the 215-225 range. I have a 180 degree t-stat installed and it had no issue keeping cool with the original engine. Are these engines prone to have air pockets that get stuck or is there something else...

Autometer gauge pod SOLD! Leaving this pic to show the WB and shift light operating. AEM Wideband Oxygen sensor gauge (AEM 30-4100). Sensor is about 2 years old (Bosch LSU4.2). Gauge works fine as seen in the picture above. No mounting hardware. I had it in the gauge pod listed above...

Steve, Price on 5C3Z-6N881-AA and 5C3Z-6N881-BA please. Thanks CSR

I bought aftermarket Sealed Power timing chain tensioners for my 3V build. The engine makes a fair bit of timing chain noise on initial startup, which seems to point to the tensioners bleeding down. Could it be anything else or is this another "should have bought OEM" kind of thing...

I'm working on the tune for my new 5.0L build (5.0L cammer block). I have 10 degree limiters in the phasers and the tune is calling for zero cam retard essentially for all but WOT higher RPM conditions right now. I'm logging "Cam Angle" and "Cam Angle2" PIDs and am reading anywhere from 3 to...

I'm going to be putting together an automatic setup for my car this fall/winter. What does anyone think the TR3650 and all supporting conversion parts are going to be worth? The transmission is rebuilt including a new 2nd gear, Exedy clutch, Fidanza aluminum flywheel (steel included too I...

Are all 4R70W transmissions the same? Meaning, if I have one that came out of a 2WD truck with a 4.6L can I rebuild it and expect to use it in a S197?

nevermind, I found what I was looking for

Does anyone have a calculation to correlate how much material removed from the deck surface equals a certain amount of reduction in combustion chamber CCs on a stock 3V head?

I'm contemplating a rear seat delete and also replacing the factory front seats with some lightweight components. Is there a market for clean seats? If so, what are they worth? Power drivers seat, manual passenger and rear seat and back obviously. All black leather.

Delete Found one. Delete thread.

I'm looking for some paper or fiber type intake manifold gaskets. The stock o-ring gaskets won't work for what I'm doing. I seem to remember one of the super charger kits on the market uses paper gaskets, but haven't been able to find them. Any ideas? Thanks