Search results for query: *

  • Users: Rypper1
  • Content: Threads
  • Order by date
  1. R

    Wipers only on high

    My 12 GT drivers side windshield drain had plugged up making it hold water. During a big rain storm the water got high enough to short out the wiper motor. Bought a new (rebuilt) motor for it and after install it only works on High and doesn't park the wipers when turned off. Is there a relay...
  2. R

    2012 Mustang GT stumbling at part throttle

    I have a 2012 Mustang GT that has developed a pretty heavy stumble at part throttle. It doesn't seem to do it at WOT, if it is I don't feel it. It developed in the last week or so. The only mods are Pypes LTH, High Flow catted H pipe, and a Lund tune. I have reloaded the tune, completed an idle...
  3. R

    Caster/Camber plates?

    Ok, I am going to be ordering some SP009 BMR Springs and I already have a clunky front end. Do I need to add caster/camber plates and will it help get rid of the clunks when crossing bumps? I read a bunch here on the GT500 strut mounts and they seem to be hit or miss. And from what I read, you...
  4. R

    Picking up knock

    Every since I got a tuner/tune my 2012 gt has been showing knock under full throttle and pulling timing. I guess it was showing it before the tuner but no way to find out. Anyway, first thing I did was put on a catch can, no help. Added Torco octane boost to see if I was getting bad gas, no...
  5. R

    Which TB on CJ Mani?

    Which throttle body works best on the Cobra Jet manifold? The 65 mm twin or the oval one? The oval looks like it would have higher flow numbers over the twin opening. Tried searching but couldn't find an answer.
  6. R

    F&R Bumper covers and R side rocker

    I ditched my car and need to replace the front and rear bumper covers and the right (passenger) side rocker. Anyone have these items they need to get rid of? Prefer Tungsten color since the car already is. Must be shipped unless close enough to pick up.
  7. R

    WTF?? Another broken plug?

    This is the second HTO plug that has broken in the same manner. The ceramic around the center electrode has broken and fallen to the grounding bar causing a misfire. The first one was on cylinder #6, this one was cylinder #4. Anyone know what can cause this? In both cases it happened at WOT in...
  8. R

    Very low oil pressure on initial start up?? New stroker build.

    I had a new short block put in with all forged stroker rotating assembly and a GT500 oil pump with TSS billet gears. When the shop cranked it up the oil pressure was extremely low so they shut it down right away and reprimed the system before trying it again. Same thing happened. Not sure what...
  9. R

    Who's short block to buy?

    I know this has been discussed before but I still have questions. Today I blew a rod and custom ported the block. What I am looking for is a short block that will handle ~500 - 550 hp. The two builds that I have found the most positive feedback on are Livernois and the FRPP Aluminator. Are there...
  10. R

    How much will Roush lowering springs lower the rear on an 06?

    I want to lower the rear end of the car to take some of the tire to fender gap out. I was looking at the Roush rear lowering springs Part #401295. I really am not looking to slam the car or anything because it has the Hellion kit on it and I don't want to start scraping everything. I just want...
  11. R

    Will a 275/40 tire fit a stock 8.5" wide rim?

    Like the title says, will a 275/40zr18 fit on the stock 18" rim? I think the stock rims are 8.5 inches, is that correct? I see that the recommended minimum size rim is 9 inches. I want to make sure that it will not cause the side wall to balloon out and look like crap and cause the tire to wear...
  12. R

    Anyone got a pic of a relocated oil filter?

    I am in the process of relocating my oil filter to make it easier to change the oil. I have a Hellion turbo on the car and it is pretty much a must do item. I am trying to find a good spot for the new filter location. I have searched but didn't find a picture that showed it very well. Thanks
  13. R

    26 Spline input shaft. Where from?

    Where are y'all getting your 26 spline input shafts from? I'm about to change out my clutch and think I need to swap out the shaft at the same time. Thanks
  14. R

    Bolts for Powerhouse aluminum driveshaft?

    I bought a used powerhouse driveshaft but the guy needed to keep the bolts. Can I reuse the ones from the stock shaft or do I need a different bolt? If so what size and grade? Thanks
  15. R

    Recommended Oil Filter Relocate kit?

    Guys, I have a Hellion turbo kit on my car and it is a pain in the ass to change the oil filter. What kit do y'all recommend to relocate the filter? Mike/Powerhouse was supposed to come out with on but I haven't seen it. Thanks
  16. R

    What do I need to pass the OBDII Inspection? Tuners?

    I have a Fastlane (in Houston) tune in my car. Today I had it inspected and it failed the OBDII test. The report says that the O2 sensor is not ready, the O2 sensor heated is not ready and the Catalyst is not ready. I think that Fastlane may have the rear O2's turned off but cannot confirm this...
  17. R

    Hellion with K Member brace and torque limiters?

    Anyone running a K Member brace with the torque limiters? I ordered it from PMP then saw a post about it not fitting with another brand of turbo. Now I am wondering if it will fit with the Hellion kit. Oh, the brace is the CHE 4 point. Thanks
  18. R

    Spec 2+ noise when engaging

    I had a Spec 2+ Clutch and Spec steel flywheel installed about 500-600 miles ago. Lately it occasionally makes a screech or squeal when engaging. I just changed the fluid and bled the system and it is still doing it. Anyone have this happen? Also the clutch is engaging about an inch off the...
  19. R

    Progressive Boost Controller on a Turbo?

    Anyone have experience with a progressive boost controller on a turbo application? Right now 1st and 2nd are basically useless for me. I have the Hellion kit with a Brenspeed tune at 9-10 psi, 4:10's, and LCA's, otherwise stock. I know the factory 18's are not that great for sticking, would it...
  20. R

    Whipple HO Fuel economy?

    What kind of MPG are y'all getting with a Whipple HO with the FRPP Tune and stock gears? Thanks Randy
  21. R

    Belt squeal problem

    My car sat up for about a month and a half due to medical problems. Now the serpentine belt is squealing like a bitch. I tried belt dressing even though they say not to use it on serpentine belts. Now when it is idling it doesn't squeal but as soon as you rev it the squeal starts and stays until...
  22. R

    Are my LCA's in backwards?

    I was searching for some information on LCA length and found a picture that makes me think mine were installed backwards. The first picture is mine and the red LCA is the picture I found. Are mine in backwards?? thanks
  23. R

    LCA length?

    I read somewhere that the LCA's on our cars are unequal in length. Can't find it now through search, must not have been on this site. Is this true? If so which side is the longer side? I put my stock ones side by side but they look the same to me. Thanks Randy
  24. R

    Clutch pedal different after Spec 2+ intall?

    I just had a Spec Stage 2+ installed on my car. I also had the slave cylinder replaced while they were at it. When I picked up the car I noticed the pedal engage/disengage point is way different than it use to be. Now the clutch is fully engaged almost as soon as it comes off the floor. And...
  25. R

    Clutch slave cylinder question

    Does the slave cylinder have to be replaced when you replace the clutch? My stock clutch is slipping and needs to be replaced, I want to get all the parts together before starting on this. If it has to be replaced, anyone know a good site online that has them? Best price I can find is about...

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Sponsor Links

Banner image
Back
Top