Search results for query: *

  1. B

    Gauge Color after PCM disconnect

    Hello, After disconnecting the PCM and turning the key to the run position, the gauge cluster glows bright red. I will be replacing the PCM with a Holley unit. Fuel gauge seems to work and all other window, fan, etc seem to be functional. Is there a way to turn off this red/warning color ...
  2. B

    2006 Mustang GT for NHRA Stock eliminator

    The class for a 2006 would be a G/SA Index is listed at 12.00 3470 pounds with driver
  3. B

    seat belt will not extend after removal

    Thanks for the tip. Could not have done it, without it. I did the 100 stroke method with no success. I clamped in a vice a fully expecting the assembly to come flying out at me a taking out my front teeth:) Then I got to thinking... I clamped the assembly in a vice vertically like is...
  4. B

    seat belt will not extend after removal

    Hello - I removed my seat belts to install my rollbar. I would like to reinstall the passenger side belts for drag strip ride-alongs. I am not able to get the belts to extend again after being completely removed from car. Anyone else ran across this before? I did have to cut the two wires...
  5. B

    Rear end " refreshing "

    I recently picked up this style of bearing puller. It doesn't hurt the bearings as bad an if your careful you may be able to reuse them check the collar sizes though. I think the 8.8 had bigger carrier bearing than my 9 inch. VEVOR Carrier & Pinion Bearing Puller-
  6. B

    Torque convertor nuts

    3/8-24 tpi threads and 10mm 1.0 pitch are very close in appearance - I struggle with these a lot . Especially when mixing brake parts and calipers.
  7. B

    Torque convertor nuts

    I'm reasonably sure mine were 10mm 1.0 pitch. At least that is what the measurement were pointing to. -BP
  8. B

    Torque convertor nuts

    I recently put a TCI convertor on my 2010 The nuts TCI sent with the Torque Converter were a different pitch than the studs on the Torque converter or the adapter plate. Brad
  9. B

    AJ1E Servo install

    Yeah - I'm 75% sure it's cut as the o-ring was hanging down it the open passage, but still appeared to be in one piece. This side is the band side so there many not be any fluid pressure at this area of the servo rod..
  10. B

    AJ1E Servo install

    Thanks- I'll take a look to see... I did this with the trans out of car. I'm wondering if when the servo spring releases during install if the o-ring retracts to a spot where it can catch on the case - past a channel opening. Probably need to make sure that when the servo is inserted it...
  11. B

    AJ1E Servo install

    AJ1E Servo Install Question... When I installed the AJ1E Servo kit, twice it cut the O-ring when pushing into the case, the teflon cover was in place so I think I had that correct- Fortunately the kit came with a few spare o-rings but I'm pretty sure the one in the trans now is also cut...
  12. B

    Rear bumper brackets??

    I have had reasonable good luck with Autofit.com Their website is a bit weak but I have picked up most of my parts in person here in PHX. I have gotten fender and a grill surround here.
  13. B

    2010 4.6 3v Engine Wire harness source ?

    An update .. I was able to push the pins out of the connector housing using a de-pinning tool. I added shrink tubing around each bare wire and reinstalled. A replacement connector is available from Napa but it does have more wires than required so you probably would end up de-pinning some...
  14. B

    2010 4.6 3v Engine Wire harness source ?

    I checked with Ray at Petrie. Super guy,great to work with. AR3Z-12A581-DB Is the correct part number for an auto. -BB is the part for manual shift. Unfortunately there are none of either in stock anywhere. I guess I will try to push the pins out of the connector and add some shrink...
  15. B

    2010 4.6 3v Engine Wire harness source ?

    There should be a difference between Auto and Manual trans harness. I can't tell which part is correct from their diagrams. I'll give them a call to see if they can determine which part number is correct for a 5r55 Auto. Brad
  16. B

    2010 4.6 3v Engine Wire harness source ?

    Thank You - I'll let you know how it works out. Brad
  17. B

    2010 4.6 3v Engine Wire harness source ?

    Hi, Can you share your source? Ford Parts Giant shows part unavailable when I view Ford AR3Z-12A581-DB Wire Assembly Thanks, Brad
  18. B

    2010 4.6 3v Engine Wire harness source ?

    Hello - I have a 2010 GT with 5R55s I see some issues with my engine wire harness. The insulation on the o2 senors and transmission wires are coming apart and the wires are bare. Are there any sources for a new complete engine wire harness? Thanks Brad

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top