Search results for query: *

  • Users: Low Dogg
  • Content: Threads
  • Order by date
  1. Low Dogg

    Coyote Engine Swap... 2014 for 2015

    I was just thinking, with all the improvements made too the 2015 coyote engine, how hard would the swap be into a 2014 GT.... I know you will need to swap the intake, to eliminate the charge motion plates, an a tune to deal with the mid-lock cam phasers.... But it seems like it would be a...
  2. Low Dogg

    Possible problem with 6R80 trans

    I have a 2014 Mustang GT A6 with less than 12,000 miles. When I installed a aluminum driveshaft, I noticed it had some play in the output shaft of the transmission. Up, down, and side to side, seems about an 1/8 of movement. It makes no noise or vibration, even at 120 mph. Is this normal or...
  3. Low Dogg

    2011+ Stock driveshaft

    Anybody have a stock 2011+ Gt driveshaft laying around? Wanting to know the casting numbers on front u-joint flange. Should be something like C3-2-831 or something like that. Any help would be great. Thanks
  4. Low Dogg

    A6 transmission output flange bolt pattern

    Anybody know, what the bolt pattern spacing is, on a A6 transmission output flange? Iam thinking its 3 "x3" on center. Can anybody verify. Thanks
  5. Low Dogg

    Driveshaft Length

    Anybody know the stock driveshaft length?... Extended and compressed, flange to flange or u-joint to u-joint. Thanks for any help
  6. Low Dogg

    WTB: Stock Fuel Pump Wiring Harness

    Iam looking for a stock fuel pump wiring harness. From the FPDM to the tank. Needs to be complete, with all plugs. I have an 06 mustang GT, if that makes a difference. Thanks for any help.
  7. Low Dogg

    Spec Aluminum Flywheel

    I need to know if there is a difference between Spec 64A and Spec 46A. I know the 64A is listed for 96-04 mustangs and the 46A is listed for 05-up. American Muslce web site says they are the same......Why would Spec have too different part numbers for the same part? Which makes me believe they...
  8. Low Dogg

    S197 Shootout Listed on Mason Dixon Dragway Website

    I know i failed.....lol. Should have used the search.
  9. Low Dogg

    Rack & Pinion Steering Question

    Does anybody know the width of a stock power rack & pinoin? In other words,width of rack without tie rod ends. Thanks for any help.
  10. Low Dogg

    Front Strut Diminsions

    I would like to know the front strut deminsions. I need to know lower sturt mount, hole size and center to center diminsions. Would also like to know width diminsion, where spindle slides into strut. Iam sure somebody has a stock set they took off, in there garage. Thanks for any help.
  11. Low Dogg

    Coil-over Struts

    Has anybody tried using coil-overs off an older mustang? What caster, camber plates could you use? I know somebody on here has, if he wants to step forward.
  12. Low Dogg

    Steeda UDP Problems

    About a year ago i put Steeda UDP on my 06 GT. Everything was great. At the begining of this week my car deveopled a curping noise. I thought it was a bad idler pulley. I check them all and everything was good. So i left the car set at home. Started the car one day and the curping was...
  13. Low Dogg

    Need info on this wiring harness.

    I need some info on a wiring harness. The part number is 5R3Z9D353AA I beleive this is a fuel pump wiring harness, but i need to know where this runs to and from. Any help would be great. Thanks
  14. Low Dogg

    Fuel Pump Driver Module

    Iam looking for a FPDM for a 2006 Mustang GT. Iam doing a custom dual pump setup. I want one because of doing some testing. I know i can buy a new one, just want a cheap one.

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top