FS: 302 3v Stroker

[chutoyy]

It's the shipping... I'll have to schedule a pickup, make a waybill, properly pack/seal it... I've been lowballed for all my other parts so, meh.

$2500, buyer pays shipping.

 

[chutoyy]

:bump:

 

[chutoyy]

Been busy w/ new car.. junkyard didn't take it because there's oil content and 'mixed' metals....

$2800 shipped.. someone?

 

[stang67]

Oil content and mixed metals

 

[warpig12354]

It would pain me to take this to a junk yard.

 

[Blk02crewinms]

I'm gonna assume by mixed metals they were rendering to the aluminum block and the forged rotating assembley being the mixed metals.

 

[avinaj80]

Scrap yards/recyclers don't give you shit... I took an aluminum driveshaft once that was too short and they only wanted to give me $25 for it... Be patient bro, you'll find a buyer...

 

[chutoyy]

Make an offer.. it's sitting in a warehouse and they're getting annoyed that it's back.

 

[silverstang07]

Nobody is giving you that much money for it. Would be better to part it out or take a huge loss for it. If you do part out, let me know

 

[chutoyy]

Not going to waste any more time w/ this Mustang crap... I'm selling it as a whole thing...

I'm building a motor for my new car.

Nobody is giving you that much money for it. Would be better to part it out or take a huge loss for it. If you do part out, let me know

 

[skwerl]

I can't see the video because I am not registered at Facebook (and will not). I'm not fully understanding exactly what is wrong with this assembly/block combination. Can somebody explain it to me in simpleton terms?

 

[BadPiggy]

I can't see the video because I am not registered at Facebook (and will not). I'm not fully understanding exactly what is wrong with this assembly/block combination. Can somebody explain it to me in simpleton terms?

The block wasn't bored using a torque plate. That leaves a lot of room for error...cylinders not being perfectly round, for one.

Both items are worth money...but not as a unit. To get the bore squared up, it needs to be bored again using a torque plate..which will make it an overbore. Then the pistons will be too small when that's done.

 

[skwerl]

Thanks, Chris. I get it.

 

[chutoyy]

Thanks.

 

[chutoyy]

:bump: offer.

 

[DVEST8R]

I had a teksid that was done like the op's engine and it was perfectly fine....bump

 

[go302]

This isn't some big bore big block where the head studs are abnormally close to the cylinder walls. Some people take this torque plate thing a little too seriously. Unless you're building some monstrous ci motor that makes well over 1000 hp it's really not that big of a deal. As DVEST8R said, it will run just fine. This is a hell of a steal right here.

 

[chutoyy]

$2200 shipped. Moving out of state so I need this gone.

And I won't separate internals because it'll cost me even more time and money to disassemble, clean, pack, and ship. Then I still have a block no one wants (unless someone wants to make a coffee table).

 

[crownaviation]

This isn't some big bore big block where the head studs are abnormally close to the cylinder walls. Some people take this torque plate thing a little too seriously. Unless you're building some monstrous ci motor that makes well over 1000 hp it's really not that big of a deal. As DVEST8R said, it will run just fine. This is a hell of a steal right here.

This is not a iron block either. I have seen what happens when they are not used. It is not pretty. Ask any professional modular builder. ..

$2200 shipped. Moving out of state so I need this

And I won't separate internals because it'll cost me even more time and money to disassemble, clean, pack, and ship. Then I still have a block no one wants (unless someone wants to make a coffee table).

That is a great deal. . Someone will snag this for sure. The ra alone is worth more

 

[chutoyy]

:bump: