NjsGT's build.... with pics!

[GrnBullitt08]

Just go with the GT500 TB

 

[NjsGT]

Just go with the GT500 TB

yea, ill throw that into the cart of stuff to buy....

Also, I found everything ill need to make a blow-through setup with lightblades helps..... came out to be just under $300 bucks minus the BOV....

Along with....
-Steeda deleltes
-GT500 TB
-Tial 50MM BOV with 10-11psi spring
-2.87" pulley which ill pick up on a trade with NYshelby

Now I still have to make up my mind with who to tune with.....
-Efilogics
-Evolution Performance
-JDM
I think that will be decided on who's not busy packed which kinda throws out JDM haha

 

[GrnBullitt08]

Just have EFilogics tune your car. He did a good job last time.

 

[Chris06GT]

Nice build man!! Definitely a great job! Keep it up man!!

 

[Steedman07]

I would have Chris tune it..Hes tuned your car before..

 

[HOLYWD]

Nope every problem with a tb has been from aftermarket
I've seen amazing gains withthe gt500 and never one issue
Do as I say buddy ! Gt500 FTW
Powder coat it blue

 

[NjsGT]

Just have EFilogics tune your car. He did a good job last time.

I would have Chris tune it..Hes tuned your car before..

Yea, he did pull off 40-50 more HP then I expected.... And I know Chris has the car in his data base to pull up and see what he did before.... I gotta call him soon and ask if I can run my current tune with these LT's just to break in the motor since I cant really go WOT for 1000 miles.... If not maybe he could email me a update for it... I will say, he's a busy man and tough to get a hold of haha

Nice build man!! Definitely a great job! Keep it up man!!

Thanx chris!

Nope every problem with a tb has been from aftermarket
I've seen amazing gains withthe gt500 and never one issue
Do as I say buddy ! Gt500 FTW
Powder coat it blue

Ok ok... fine.... GT500 TB it is....

 

[NjsGT]

Just got done purdy'n the crank pulley up.... Needs a couple of hours to dry then im going to go down and throw it on.... Ill take some pics too

 

[GrnBullitt08]

Let me know if you need someone to powdercoat that TB.

 

[NjsGT]

Let me know if you need someone to powdercoat that TB.

Ok, thanx. Once I have it in hand ill make the decision to have it colored...

 

[GrnBullitt08]

I would coat it with a candy blue... Looks close to your valve covers

 

[KITT]

subscribed. Nice build man

 

[fhlh]

sub'd great build up, can't wait to see the final results.

 

[HOLYWD]

Tolddddd youuuuuuu

 

[NjsGT]

subscribed. Nice build man

sub'd great build up, can't wait to see the final results.

thanx guys

I would coat it with a candy blue... Looks close to your valve covers

Tolddddd youuuuuuu

haha, let me order it first!

 

[NjsGT]

Short update....

Installed the front pulley tonight....
Heres the pulley cleaned up to prevent anymore rust...

Heres it on the motor

Picked up some coolant yesterday and filter.... Oil comes tomarrow. Going with Valvoline VR1 high zinc racing oil for the break-in period as spec'd by jim jr at JDM

So im pretty much ready to drop it back into the car.... Looks like this weekend il clean off the fucking foot of new snow on the hood and jump under the hood to install the prothane motor mounts and clean it up abit under there....

 

[NjsGT]

Got to cleaning the 14" of snow off the car today so I could pop the hood and throw the Prothane bullit motor mounts on....

Before I removed the stock motor mounts... Notice the rat nest of wires I have to sort through to sneak the motor back in and make sure they all get connected to the right spots.... Christ.....

Driver side removed.... Piece of cake

Quick comparison between the stocky's and Prothane's

Driver and passenger sides both in and torqued....

Now if my bro wasnt sick, I could have this motor on its way back in.... Damn it...

 

[HOLYWD]

Great progress bud

 

[NjsGT]

Great progress bud

Thanx holy. I bet those mounts look familiar ..... haha

Also, just ordered.....
http://www.cjponyparts.com/THROTTLE-BODY-OEM-60MM-GT500-2007-2010/p/TB100/
And this.... Alittle bit larger then a vortech filter...
http://www.summitracing.com/parts/KNN-RF-1046/

Next week going to put my blow thru set order in as far as all the piping, fittings, and of coarse t-bolt clamps..... Just hoding off for now cause of afew parts not in stock till next week....

Then Im down to ordering....
-VMP tuning 3" MAF tube with SCT BA500 MAF
Decided to go with this cause my tuner Chris at efilogics would rather tune with it as tuning a blow thro setup is abit finicky...
-Delete plates
-Tial 50mm BOV with either the 10 psi or 11 psi spring....

 

[HOLYWD]

Sweet progress bud !
Yes they do !