Bullitt #2479 Build

[GrnBullitt08]

lol, i have seen them too. i have also seen people's parachutes not open and that doesn't scare me from jumping. Its alot to do with safety and procedure. I will agree that luck sometimes becomes a factor. I would like a turbo set up also but don't have the cash for that right now.

i hear you on the $$

Any kind of added power is gonna cost you big coin if done the right way. Take my advice and save the money and do it right the first time.

 

[NastyStang113]

Any kind of added power is gonna cost you big coin if done the right way. Take my advice and save the money and do it right the first time.

But you spent the money in the first place and now look at you!

 

[GrnBullitt08]

But you spent the money in the first place and now look at you!

yeah but I also didnt spend the extra cash to pay the pros to do it so thats why i ended up in this position.

 

[GrnBullitt08]

This is the guy that did mine

 

[BubbaRATM]

Goodluck with the N20, should see some good power gains. You have a tune ready for it too I hope and some new injectors?


dont think i will need injectors for just a 100 shot and i am going to have bbr write me a nitrous tune after the kit gets here.

 

[NastyStang113]

yeah but I also didnt spend the extra cash to pay the pros to do it so thats why i ended up in this position.

This is the guy that did mine

Just bustin' your balls.

 

[GrnBullitt08]

Goodluck with the N20, should see some good power gains. You have a tune ready for it too I hope and some new injectors?


dont think i will need injectors for just a 100 shot and i am going to have bbr write me a nitrous tune after the kit gets here.

Oh ok, I've been talking to BBR myself about writing a new tune for my car. Ive been told that the delete plates wont yeild much of a power gain since im not running forced induction anymore or cams. Is this true?

 

[GrnBullitt08]

Just bustin' your balls.

my balls have been busted enough lately when it comes to this car lol.

 

[GrnBullitt08]

After getting the sensors switched I went ahead a ran the car for a short time....lets just say it needs a little tuning.



But hey it gives you a chance to hear the 3" dynomax system.

 

[GrnBullitt08]

Also went to look at the old motor some more and I ran into a small snag....

 

[BubbaRATM]

Oh ok, I've been talking to BBR myself about writing a new tune for my car. Ive been told that the delete plates wont yeild much of a power gain since im not running forced induction anymore or cams. Is this true?

true, so sell them to me for $10 they are junk anyway LOL j/k

i have heard they are good for about 10 hp gain on n/a but thats about it, also seen a thread the other day where i seen that they actually were added to increase low end torque, the butterflys help atomize the fuel and air at low rpm's. Down side is they restrict the flow in the mid and upper rpm range. i will see if i can find the thread again but i think it was in the 4.6 tech under the DIY CMDP's not 100% on that.

 

[BubbaRATM]

Also went to look at the old motor some more and I ran into a small snag....

is that a cat? really blurry.

 

[rford426]

i hear you on the $$

Any kind of added power is gonna cost you big coin if done the right way. Take my advice and save the money and do it right the first time.

I'm going forged I have bad luck abd not gonna have any reason for failure my uncle and grandpa will be assisting me and it's nit there first rodeo

 

[BubbaRATM]

also that 3 in dynomax sounds mean, i may have to get my buddy to hook me up with the 3in magnaflow system.

 

[GrnBullitt08]

is that a cat? really blurry.

Yeah its someones cat...not mine. Pic was from my iphone, its very blurry.

 

[GrnBullitt08]

also that 3 in magnaflow sounds mean, i may have to get my buddy to hook me up.

Yes, 3" yields a mean, deep, aggressive tone. A vid does no justice, you gotta hear it in person.

 

[BubbaRATM]

Yeah its someones cat...not mine. Pic was from my iphone, its very blurry.

he was probably crawling out of a hole from a rod LOL

 

[GrnBullitt08]

I'm going forged I have bad luck abd not gonna have any reason for failure my uncle and grandpa will be assisting me and it's nit there first rodeo

Yeah, my uncle and old man helped me with the rebuild. Mainly the old man though. His knowledge would of been useful the first time around.

 

[GrnBullitt08]

he was probably crawling out of a hole from a rod LOL

yeah...prob my engine builders cat coming to sabatoge my new motor. lol.

 

[BubbaRATM]

Yes, 3" yields a mean, deep, aggressive tone. A vid does no justice, you gotta hear it in person.

i had to edit it , i called it magnaflow, yours is dynomax correct?

im trying to look up how to test voltage on RCA cables and watch the ultimate fighter and talk here ..... multi tasking