Installing a paxton novi 2200.

[Trousersnake]

I've already got two races lined up..

Heads cam intake 100 shot c5 z06

Whipple on 18 psi with a 125 shot terminator convertible

Both are my good friends. Hope Ken B. and Terry ring every ounce out of a 93 tune while leaving me confident it wont explode.. I think I will be a contender

They both have not made 1 clean pass at the track yet.. So I've got that going for me plus leaving on IRS spraying out of the hole they should both have to do everything right.

Cobra traps 125 no nitrous
Vette goes 123 no nitrous

 

[stretch]

Since this is the unofficial 2200 thread and it was falling down the list too far I wanted to ask a question. Guess who's joining the 2200 club?

<----this guy.

Just ordered it a few minutes ago from beefcake. Thanks for reading.

im contemplating leaving the 2200 club.

 

[D98GT]

I'm contemplating joining the 2200 club once Stretch hooks me up

 

[gizmo5]

im contemplating leaving the 2200 club.

Why!?!?! You've had great success with it. :-/

 

[Wnt2gofst]

im contemplating leaving the 2200 club.

You may not be only one. But I will be leaving Mustang altogether if it goes. Just running some numbers and stuff before make final decision.

Just Another 700whp DD 5.0

 

[Wnt2gofst]

I've already got two races lined up..

Heads cam intake 100 shot c5 z06

Whipple on 18 psi with a 125 shot terminator convertible

Both are my good friends. Hope Ken B. and Terry ring every ounce out of a 93 tune while leaving me confident it wont explode.. I think I will be a contender

They both have not made 1 clean pass at the track yet.. So I've got that going for me plus leaving on IRS spraying out of the hole they should both have to do everything right.

Cobra traps 125 no nitrous
Vette goes 123 no nitrous

You will have advantage at the track with the auto to them banging gears. The c5z have went e 9's with h/c before spray. But that with good driver actually hooking on bigs/little's. His trap is low for n/a.





Just Another 700whp DD 5.0

 

[DSargent09]

Why are you two above considering leaving the 2200s? What are you thinking about switching to.

 

[Misfit_5.0]

You may not be only one. But I will be leaving Mustang altogether if it goes. Just running some numbers and stuff before make final decision.

Just Another 700whp DD 5.0

What happened to honey badgers not giving a shit and running their car until it pops, then rebuilding it?

 

[gizmo5]

What happened to honey badgers not giving a shit and running their car until it pops, then rebuilding it?

He ain't getting rid of it... ;-) I'm gonna convince him to gut it and go outlaw! lol

 

[bigriff85]

My maf is pegging out gonna hopefully be able to rescale and extend it but so far on 9.5:1 aluminator with 93 it made 640/525 at 6k at 12psi (2.95 pulley) 15 degrees of timing ...gonna have to back timing out too so it lives lol

 

[Misfit_5.0]

He ain't getting rid of it... ;-) I'm gonna convince him to gut it and go outlaw! lol

Peer pressure is a mother fucker!

 

[stretch]

Why!?!?! You've had great success with it. :-/

i get bored quick.

 

[gizmo5]

i get bored quick.

I understand... lol. Good luck with whatever you do

 

[gizmo5]

Who has a 8 rib 3.15" pulley they wanna give me?

 

[Wicked97]

im contemplating leaving the 2200 club.

Turbo or YSI club?

 

[cyclerick]

Anyone know where I can get some 5/8" PCV tubing like the stuff supplied with the kit? Only thing local is heater hose which is not oil rated. Looked on web and only found large quantities from Gates. I need about 8' for my PCV/catch can set up. I don't want to do the full steel braided stuff.

 

[TW1NTRB0]

The Fragola nylon braided stuff is nice. That's what I used on my catch can setup. Bought it from Summit Racing.

 

[Wnt2gofst]

What happened to honey badgers not giving a shit and running their car until it pops, then rebuilding it?

THIS HAPPENED!



But gizmo5 said he's not letting me trade. Lol

Just Another 700whp DD 5.0

 

[stretch]

Turbo or YSI club?

turbo, if i leave ..... but moma said if it aint broke dont fix it.....

i need a 3.15 pulley too.

 

[onebadgsx]

just ordered a complete t-bolt clamp set up for the discharge side. $100 shipped for all 20 clamps shipped.

you need

9 for 3.25 o.d hose
4 for 3.50 o.d. hose
4 for 3.75 o.d. hose
3 for 4.25 o.d. hose